Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274067 THEFT DETERRENT SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U149717E05
1.625,1.5 1.865,1.25 1.865,1.25 1.948,1.25 false 1.625,1.854 1.865,1.615 1.865,1.615 1.948,1.615 false 1.625,2.167 1.865,1.927 1.865,1.927 1.948,1.927 false 0.896,1.594 1.104,1.75 0.208,0.156 10 false 2F 1.094,3.865 1.375,4.021 0.281,0.156 10 false F10 0.896,2.188 1.104,2.344 0.208,0.156 10 false 2D 5.854,1.521 6.063,1.677 0.208,0.156 10 false 2B 5.854,2.219 6.063,2.375 0.208,0.156 10 false 2C 1.063,2.75 1.271,2.906 0.208,0.156 10 false 2E 3.75,1.344 3.865,1.49 0.115,0.146 10 false A 1.969,1.188 2.24,1.333 0.271,0.146 10 false F8 1.969,1.542 2.24,1.688 0.271,0.146 10 false F9 1.969,1.865 2.24,2.01 0.271,0.146 10 false F10 3.625,3.865 3.823,4.021 0.198,0.156 10 false F9 1.135,5.167 1.354,5.323 0.219,0.156 10 false 2F 1.885,6.396 2.104,6.552 0.219,0.156 10 false 2B 4.927,6.396 5.146,6.552 0.219,0.156 10 false 2C 3.51,7.667 3.646,7.823 0.135,0.156 10 false A 3.938,5.177 4.135,5.333 0.198,0.156 10 false 2D 5.896,5.177 6.094,5.333 0.198,0.156 10 false 2E 5.958,3.833 6.156,3.99 0.198,0.156 10 false F8

a.

b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Auxiliary battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Auxiliary battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
F10-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.



d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V
F8-3 (LCTY) - Body ground V - Body ground Rear door LH courtesy light switch input Rear door LH open Below 1 V
F8-3 (LCTY) - Body ground V - Body ground Rear door LH courtesy light switch input Rear door LH closed 11 to 14 V
F9-6 (RCTY) - Body ground R - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V
F9-6 (RCTY) - Body ground R - Body ground Rear door RH courtesy light switch input Rear door RH closed 11 to 14 V
F9-11 (L2) - Body ground LG - Body ground Driver side door key-linked lock input Driver side door key cylinder lock position Below 1 V
F9-11 (L2) - Body ground LG - Body ground Driver side door key-linked lock input Ignition switch off, all doors closed and driver side door key cylinder neutral position Pulse generation (See waveform 1 or 2)
F9-24 (UL3) - Body ground GR - Body ground Driver side door key-linked unlock input Driver side door key cylinder unlock position Below 1 V
F9-24 (UL3) - Body ground GR - Body ground Driver side door key-linked unlock input Ignition switch off, all doors closed and driver side door key cylinder neutral position Pulse generation (See waveform 3 or 4)
F9-7 (LSFL) - Body ground G - Body ground Front door LH lock position switch input Front door LH unlocked Below 1 V
F9-7 (LSFL) - Body ground G - Body ground Front door LH lock position switch input Ignition switch off, all doors closed and front door LH locked Pulse generation (See waveform 5 or 6)
F9-18 (LSFR) - Body ground G - Body ground Front door RH lock position switch input Front door RH unlocked Below 1 V
F9-18 (LSFR) - Body ground G - Body ground Front door RH lock position switch input Ignition switch off, all doors closed and front door RH locked Pulse generation (See waveform 7 or 8)
2F-25 (LSWL) - Body ground V - Body ground Rear door LH lock position switch input Rear door LH unlocked Below 1 V
2F-25 (LSWL) - Body ground V - Body ground Rear door LH lock position switch input Ignition switch off, all doors closed and rear door LH locked Pulse generation (See waveform 9 or 10)
F10-2 (LSWR) - Body ground V - Body ground Rear door RH lock position switch input Rear door RH unlocked Below 1 V
F10-2 (LSWR) - Body ground V - Body ground Rear door RH lock position switch input Ignition switch off, all doors closed and rear door RH locked Pulse generation (See waveform 11 or 12)
2B-34 (IND) - Body ground L - Body ground Security indicator light signal Security indicator light illuminates (illuminates only for 30 (+/-5) seconds in alarm sounding state (blinks when system in armed state)) 3 to 6 V
2D-23 (HCTY) - Body ground B - Body ground Security courtesy switch input Engine hood open Below 1 V
2D-23 (HCTY) - Body ground B - Body ground Security courtesy switch input Engine hood closed Pulse generation (See waveform 13 or 14)
2D-29 (HORN) - Body ground GR-L - Body ground Vehicle horn(s) signal Vehicle horn(s) sounding (theft warning system in alarm sounding state) Pulse generation
2D-29 (HORN) - Body ground GR-L - Body ground Vehicle horn(s) signal Vehicle horn(s) not sounding (theft warning system in armed state) 11 to 14 V
2D-25 (SH) - Body ground R - Body ground Security horn signal Security horn sounding (theft warning system in alarm sounding state) Pulse generation
2D-25 (SH) - Body ground R - Body ground Security horn signal Security horn not sounding (theft warning system in armed state) 11 to 14 V

If the result is not as specified, the main body ECU or driver side junction block assembly may have a malfunction.


e.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) F9-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder neutral position


f.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) F9-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder neutral position


g.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) F9-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder neutral position


h.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) F9-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder neutral position


i.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) F9-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door LH locked


j.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) F9-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door LH locked


k.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 7.

Waveform 7 (Reference)
Item Content
Terminal No. (Symbol) F9-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door RH locked


l.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 8.

Waveform 8 (Reference)
Item Content
Terminal No. (Symbol) F9-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door RH locked


m.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 9.

Waveform 9 (Reference)
Item Content
Terminal No. (Symbol) 2F-25 (LSWL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door LH locked


n.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 10.

Waveform 10 (Reference)
Item Content
Terminal No. (Symbol) 2F-25 (LSWL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door LH locked


o.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 11.

Waveform 11 (Reference)
Item Content
Terminal No. (Symbol) F10-2 (LSWR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door RH locked


p.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 12.

Waveform 12 (Reference)
Item Content
Terminal No. (Symbol) F10-2 (LSWR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door RH locked


q.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 13.

Waveform 13 (Reference)
Item Content
Terminal No. (Symbol) 2D-23 (HCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and engine hood closed


r.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 14.

Waveform 14 (Reference)
Item Content
Terminal No. (Symbol) 2D-23 (HCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and engine hood closed



CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


U149777E03
4.115,0.406 4.521,0.604 0.406,0.198 10 false W10 2.833,0.406 3.177,0.583 0.344,0.177 10 false V2

a.

Disconnect the V2 multiplex network door ECU (back door P/W) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground B - Body ground Battery power supply Always 11 to 14 V
V2-7 (BECU) - Body ground L - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the V2 multiplex network door ECU (back door P/W) connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W10-10 (BDCY) - W10-18 (CTYE) P - G Back door courtesy switch input Back door closed Pulse generation (See waveform 1 or 2)
W10-10 (BDCY) - W10-18 (CTYE) P - G Back door courtesy switch input Back door open Below 1 V
W10-16 (BKL) - W10-8 (KEYE) P - V Tail gate control switch lock input Back door lock key cylinder neutral position Pulse generation (See waveform 3 or 4)
W10-16 (BKL) - W10-8 (KEYE) P - V Tail gate control switch lock input Back door lock key cylinder is turned lock Below 1 V
W10-15 (BKUL) - W10-8 (KEYE) R - V Tail gate control switch unlock input Back door lock key cylinder neutral position Pulse generation (See waveform 3 or 4)
W10-15 (BKUL) - W10-8 (KEYE) R - V Tail gate control switch unlock input Back door lock key cylinder is turned unlock Below 1 V

If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.


e.
B245381E01
0.178,0.926 0.517,1.093 0.339,0.166 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) W10-10 (BDCY) - W10-18 (CTYE)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door closed


f.
B245382E01
0.179,0.927 0.518,1.094 0.339,0.166 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) W10-10 (BDCY) - W10-18 (CTYE)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door closed


g.
B245381E01
0.178,0.926 0.517,1.093 0.339,0.166 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol)
·

W10-16 (BKL) - W10-8 (KEYE)

·

W10-15 (BKUL) - W10-8 (KEYE)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door lock key cylinder neutral position


h.
B245382E01
0.179,0.927 0.518,1.094 0.339,0.166 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol)
·

W10-16 (BKL) - W10-8 (KEYE)

·

W10-15 (BKUL) - W10-8 (KEYE)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door lock key cylinder neutral position