Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274067 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is in the alarm sounding state, the main body ECU outputs a signal repeatedly at 0.4 second intervals, causing the security horn assembly to sound

WIRING DIAGRAM

B184350E04
0.297,0.674 0.813,1.059 0.516,0.385 10 from Battery 1.333,0.896 2.115,1.085 0.783,0.189 10 SECURITY 2.676,1.458 3.241,1.648 0.565,0.189 10 S-HORN 5.542,0.747 5.792,0.918 0.250,0.171 10 SH 5.264,0.662 5.480,0.810 0.216,0.148 10 17 5.368,1.593 5.646,1.752 0.278,0.159 10 A 5.368,1.733 7.032,2.088 1.664,0.355 10 Main Body ECU (Multiplex Network Body ECU) 3.856,1.823 4.244,2.035 0.387,0.211 10 A32 3.856,1.975 4.734,2.285 0.878,0.310 10 Security Horn Assembly 3.546,1.864 3.769,2.059 0.223,0.195 10 1 3.28,0.624 3.502,0.819 0.223,0.195 10 1 2.537,0.624 2.711,0.819 0.174,0.195 10 2 2.523,1.198 2.649,1.394 0.126,0.195 10 5 3.28,1.198 3.502,1.394 0.223,0.195 10 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY HORN)
a.

Operate the intelligent tester according to the steps on the display and select Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Horn Security horn ON/OFF -

OK:

Security horn operates normally.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT S-HORN RELAY
2.INSPECT S-HORN RELAY
a.
E145692E28
2.656,0.74 3.031,0.74 false 1.615,0.729 2,0.729 false 2.531,1.135 3.052,1.135 false 2.531,1.635 3.042,1.635 false 0.219,1.281 0.375,1.458 0.156,0.177 10 false 1 1.198,1.281 1.354,1.458 0.156,0.177 10 false 2 0.219,0.74 0.375,0.917 0.156,0.177 10 false 3 1.198,0.74 1.354,0.917 0.156,0.177 10 false 5 1.5,0.635 1.656,0.813 0.156,0.177 10 false 1 3.063,0.646 3.219,0.823 0.156,0.177 10 false 2 3.083,1.542 3.24,1.719 0.156,0.177 10 false 3 3.104,1.042 3.26,1.219 0.156,0.177 10 false 5

Remove the S-HORN relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

3.INSPECT SECURITY HORN ASSEMBLY

NG

REPLACE S-HORN RELAY

3.INSPECT SECURITY HORN ASSEMBLY

b.

Apply battery voltage to the horn connector and check the operation of the horn.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Horn bracket
Horn sounds




OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU, SECURITY HORN AND BATTERY)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU, SECURITY HORN AND BATTERY)
a.

Remove the S-HORN relay from the engine room relay block.


b.

c.

Disconnect the A32 horn connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay block S-HORN relay terminal 1 - A-17 (SH) Always Below 1 Ω
Relay block S-HORN relay terminal 3 - A32-1 Always Below 1 Ω
A-17 (SH) - Body ground Always 10 kΩ or higher
A32-1 - Body ground Always 10 kΩ or higher



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay block S-HORN relay terminal 2 - Body ground Always 11 to 14 V
Relay block S-HORN relay terminal 5 - Body ground Always 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR