Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274067 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator light flashes continuously when the engine immobiliser system is set, and does not illuminate when the engine immobiliser system is not set.

When the theft deterrent system is in the armed state, the engine immobiliser system is automatically set and the security indicator light flashes continuously.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the main body ECU causes the security indicator light to be illuminated.


WIRING DIAGRAM

B242452E01
0.99,1.994 3.095,2.160 2.105,0.166 10 Telltale Light Assembly 1.252,1.147 2.715,1.310 1.463,0.163 10 Security Indicator Light 3.229,1.443 3.385,1.629 0.156,0.186 10 E 3.152,0.901 3.427,1.087 0.275,0.186 10 LP 3.427,1.393 3.789,1.579 0.362,0.186 10 1 3.426,0.851 3.732,1.037 0.306,0.186 10 2 4.654,0.851 4.847,1.037 0.194,0.186 10 23 4.119,2.005 4.313,2.191 0.194,0.186 10 A 0.993,1.828 1.293,2.013 0.300,0.186 10 F32 4.935,0.98 5.259,1.166 0.324,0.186 10 IND 4.119,2.156 7.063,2.335 2.944,0.179 10 Main Body ECU (Multiplex Network Body ECU)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Operate the intelligent tester according to the steps on the display and select Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF The test is possible when the following conditions are met:
·

The key is in the ignition key cylinder



OK:

Security indicator light can be turned on and off using the intelligent tester.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT TELLTALE LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)
2.INSPECT TELLTALE LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)
a.
B216769E07
2.375,1.177 2.594,1.542 false 2.052,1.177 1.833,1.542 false 2.583,1.552 2.708,1.76 0.125,0.208 10 false E 1.74,1.542 1.938,1.75 0.198,0.208 10 false LP

Remove the telltale light (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL).


b.

Apply battery voltage between the terminals of the telltale light assembly and check that the security indicator light illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (LP)
Battery negative (-) → 1 (E)
Security indicator light illuminates




OK

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT - MAIN BODY ECU AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the F32 light connector.


b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-2 (LP) - A-23 (IND) Always Below 1 Ω
F32-1 (E) - Body ground Always Below 1 Ω
F32-2 (LP) or A-23 (IND) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR