Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056157 LIGHTING (INT) _0274081 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Overhead Console Illumination Light Circuit  


DESCRIPTION

The main body ECU controls the center console spot light.

WIRING DIAGRAM

E199775E07
5.073,1.958 6.729,2.333 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.073,1.771 5.323,1.927 0.25,0.156 10 false F8 2.635,1.271 4.333,1.646 1.698,0.375 10 false Map Light Assembly (Center Console Spot Light) 2.635,1.104 2.885,1.26 0.25,0.156 10 false U2 0.344,0.719 1.135,0.906 0.792,0.188 10 false from Battery 1.771,0.875 2.24,1.063 0.469,0.188 10 false DOME 2.781,0.719 3.208,0.906 0.427,0.188 10 false ACC1 2.531,0.594 2.677,0.771 0.146,0.177 10 false 8 5.521,0.708 6,0.896 0.479,0.188 10 false CSPT 5.271,0.594 5.417,0.771 0.146,0.177 10 false 5 3.865,0.719 4.177,0.906 0.313,0.188 10 false CILL 4.333,0.594 4.552,0.771 0.219,0.177 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CENTER CONSOLE SPOT LIGHT)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Center Console Spot LGT Center console spot light ON/OFF -

OK:

Center console spot light comes on.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.
E198779E09
0.813,1.146 1.167,1.167 true 1.5,0.615 1.427,1.167 true 0.479,1.052 0.771,1.219 0.292,0.167 10 false CILL 1.365,0.406 1.75,0.583 0.385,0.177 10 false ACC1

Remove the map light (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Connect a positive (+) lead from the battery to terminal 8 (ACC1) and a negative (-) lead to terminal 10 (CILL).


c.

Check that the center console spot light comes on.

OK:

Center console spot light comes on.




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - MAP LIGHT ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - MAP LIGHT ASSEMBLY)
a.
U181048E01
2.437,0.358 2.857,0.531 0.420,0.173 10 ACC1 2.081,1.191 2.293,0.44 2.293,0.44 2.396,0.44 false 0.211,0.175 0.408,0.345 0.198,0.170 10 *a 1.627,0.472 1.869,0.642 0.243,0.170 10 U2

Disconnect the U2 map light connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U2-8 (ACC1) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Map Light Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the U2 map light connector.


b.

Disconnect the F8 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U2-10 (CILL) - F8-5 (CSPT) Always Below 1 Ω
U2-10 (CILL) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR