Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2013.08
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the master cylinder solenoid (skid control ECU).

WIRING DIAGRAM

E244304E02
1.26,0.375 1.594,0.552 0.333,0.177 10 false SP1 1.656,0.365 1.875,0.531 0.219,0.167 10 false 12 0.469,1.146 2.063,1.792 1.594,0.646 10 false Master Cylinder Solenoid (Skid Control ECU) 0.469,1 0.75,1.177 0.281,0.177 10 false A6 5.229,0.344 5.427,0.5 0.198,0.156 10 false SI 4.917,0.354 5.146,0.531 0.229,0.177 10 false 29 5.229,1.938 5.479,2.146 0.25,0.208 10 false +S 4.938,1.948 5.167,2.104 0.229,0.156 10 false 28 3.813,1.875 4.031,2.042 0.219,0.167 10 false 20 0.094,5.969 2.917,6.313 2.823,0.344 10 false *1: w/ Radio and Display Receiver Assembly 4.917,2.615 6.792,2.958 1.875,0.344 10 false Combination Meter Assembly 4.927,2.458 5.25,2.625 0.323,0.167 10 false F14 2.792,3.146 4.156,3.396 1.365,0.25 10 false No. 4 Junction Block 2.906,2.083 3.146,2.24 0.24,0.156 10 false 4A 3.802,2.083 4.021,2.25 0.219,0.167 10 false 4B 3.823,2.406 4.063,2.573 0.24,0.167 10 false 16 3.813,2.615 4.052,2.792 0.24,0.177 10 false 4C 2.917,1.875 3.104,2.031 0.188,0.156 10 false 90 1.875,1.979 2.188,2.135 0.313,0.156 10 false 17 0.583,2.875 2.344,3.26 1.76,0.385 10 false Radio and Display Receiver Assembly*1 1.417,1.99 1.781,2.167 0.365,0.177 10 false SPD 0.583,2.708 0.99,2.865 0.406,0.156 10 false G29 2.802,5.51 4.156,5.708 1.354,0.198 10 false No. 5 Junction Block 3.823,3.698 4.042,3.875 0.219,0.177 10 false 25 1.875,3.792 2.188,3.948 0.313,0.156 10 false 18 0.771,4.719 1.146,5.052 0.375,0.333 10 false ECM 1.406,3.813 1.729,4 0.323,0.188 10 false SPD 0.094,6.344 3.104,6.688 3.01,0.344 10 false *2: w/ TOYOTA Parking Assist-sensor System 3.813,3.896 4.031,4.063 0.219,0.167 10 false 5B 2.906,3.917 3.156,4.104 0.25,0.188 10 false 5B 2.958,4.26 3.052,4.417 0.094,0.156 10 false 2 2.906,4.469 3.146,4.635 0.24,0.167 10 false 5B 0.781,4.542 1.188,4.698 0.406,0.156 10 false F51 5.313,5.854 6.552,6.25 1.24,0.396 10 false Clearance Warning ECU Assembly*2 3.813,4.833 4.021,5 0.208,0.167 10 false 73 5.313,5.688 5.625,5.854 0.313,0.167 10 false F78 3.792,5.042 4.021,5.208 0.229,0.167 10 false 5A 2.927,4.833 3.125,5 0.198,0.167 10 false 13 2.917,5.042 3.167,5.24 0.25,0.198 10 false 5A 2.927,3.698 3.125,3.875 0.198,0.177 10 false 14 5.406,4.948 5.75,5.125 0.344,0.177 10 false SPD 5.198,4.958 5.313,5.115 0.115,0.156 10 false 5

PROCEDURE

1.CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
U150510E01
0.811,0.467 1.070,0.627 0.260,0.160 10 F14 1.37,1.796 1.574,1.956 0.204,0.160 10 +S 0.207,0.089 0.383,0.249 0.176,0.160 10 *a 1.501,1.46 1.501,1.76 false

Disconnect the F14 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F14-28 (+S) - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION BLOCK)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the A6 master cylinder solenoid (skid control ECU) connector.


U150514E01
2.749,0.298 3.030,0.452 0.281,0.153 10 SP1 0.712,0.359 0.915,0.503 0.203,0.144 10 A6 0.17,0.094 0.342,0.238 0.172,0.144 10 *a 2.457,0.831 2.594,0.392 2.594,0.392 2.701,0.392 false

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-12 (SP1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid (Skid Control ECU))



OK

3.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MASTER CYLINDER SOLENOID)
3.CHECK COMBINATION METER ASSEMBLY (SPEED SIGNAL)
a.
U150516E01
2.526,1.697 2.690,1.846 0.165,0.149 10 SI 0.229,0.992 0.495,1.142 0.267,0.149 10 F14 1.333,4.089 1.457,4.238 0.124,0.149 10 A 2.97,3.521 3.303,3.671 0.333,0.149 10 GND 1.882,1.274 2.371,1.763 2.371,1.763 2.475,1.763 false

Check the input waveform.

i.

Reconnect the F14 combination meter assembly connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal F14-29 (SI) and body ground.


iv.

Turn the ignition switch to ON.


v.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Terminal No. (Symbol) F14-29 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approx. 20 km/h (12 mph)

OK:

The waveform displayed is as shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MASTER CYLINDER SOLENOID)
a.

Disconnect the F14 combination meter assembly connector.


b.

Disconnect the A6 master cylinder solenoid (skid control ECU ) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-29 (SI) - A6-12 (SP1) Always Below 1 Ω
A6-12 (SP1) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION BLOCK)
a.

Disconnect the F14 combination meter assembly connector.


b.

Disconnect the 4B No. 4 junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-28 (+S) - 4B-20 Always Below 1 Ω
F14-28 (+S) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK)
a.

Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.


i.

Disconnect the 4A No. 4 junction block connector.

U181058E02
5.792,2.406 5.635,2.406 false 4.635,0.865 5.938,0.448 false 4.844,4.448 6.031,4.552 false 5.969,0.833 6.135,1 0.167,0.167 10 false *a 3.75,0.49 3.99,0.667 0.24,0.177 10 false 4C 5.99,0.323 6.458,0.51 0.469,0.188 10 false 4C-16 6.083,4.458 6.552,4.625 0.469,0.167 10 false 4A-90 1.729,0.958 1.896,1.125 0.167,0.167 10 false *1 3.771,1.875 4.021,2.031 0.25,0.156 10 false 4B 3.802,3.417 4.083,3.604 0.281,0.188 10 false 4A

Text in Illustration
*1 No. 4 Junction Block - -
*a Front view of wire harness connector
(to No. 4 Junction Block)
- -


ii.

Disconnect the 4C No. 4 junction block connector.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4C-16 - Body ground Ignition switch ON 4.5 to 14 V
4A-90 - Body ground Ignition switch ON 4.5 to 14 V


Result
Result Proceed to
Voltage is not present in one circuit A
Voltage is present in all the circuits B




A

7.SYSTEM CHECK

B

REPLACE NO. 4 JUNCTION BLOCK

7.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in the previous step.

Result
Tester Connection System that Uses the Circuit Proceed to
4C-16 - Body ground SFI system, TOYOTA parking assist-sensor system*1 A
4A-90 - Body ground Audio and visual system B

*1: w/ TOYOTA Parking Assist-sensor System




A

8.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - NO. 5 JUNCTION BLOCK)

B

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER CIRCUIT)
8.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION BLOCK - NO. 5 JUNCTION BLOCK)
a.

Disconnect the 4C No. 4 junction block connector.


b.

Disconnect the 5B No. 5 junction block connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-16 - 5B-25 Always Below 1 Ω
4C-16 - Body ground Always 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (NO. 5 JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 5 JUNCTION BLOCK)
a.

Disconnect the 5A No. 5 junction block connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5B-2 - 5A-13 Always Below 1 Ω
5B-2 - Body ground Always 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (NO. 5 JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 5 JUNCTION BLOCK)
a.

Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.

i.

Disconnect the 5C No. 5 junction block connector.

U181074E02
4.51,2.156 5.729,1.927 false 4.406,4.354 5.75,4.448 false 6.427,2.24 6.531,2.24 false 5.646,0.844 6.417,0.844 6.417,0.844 6.417,2.24 false 1.625,0.927 1.854,1.135 0.229,0.208 10 false *1 3.802,1.76 4.031,1.969 0.229,0.208 10 false 5B 3.802,0.531 4.031,0.74 0.229,0.208 10 false 5C 3.802,3.427 4.031,3.635 0.229,0.208 10 false 5A 5.75,1.781 6.177,1.958 0.427,0.177 10 false 5B-14 5.792,4.365 6.219,4.542 0.427,0.177 10 false 5A-73 6.573,2.115 7,2.292 0.427,0.177 10 false *a

Text in Illustration
*1 No. 5 Junction Block - -
*a Front view of wire harness connector
(to No. 5 Junction Block)
- -


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5B-14 - Body ground Ignition switch ON 4.5 to 14 V
5A-73 - Body ground*1 Ignition switch ON 4.5 to 14 V


*1: w/ TOYOTA Parking Assist-sensor System


Result
Result Proceed to
Voltage is not present in one circuit A
Voltage is present in all the circuits B




A

11.SYSTEM CHECK

B

REPLACE NO. 5 JUNCTION BLOCK

11.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in the previous step.

Result
Tester Connection System that Uses the Circuit Proceed to
5B-14 - Body ground SFI system A
5A-73 - Body ground*1 TOYOTA Parking Assist-sensor System B

*1: w/ TOYOTA Parking Assist-sensor System




A

12.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT)

B

14.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU CIRCUIT)
12.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT)
a.

Disconnect the F51 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-18 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER CIRCUIT)
a.

Disconnect the G29 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

U181055E01
3.814,1.762 4.005,1.904 0.191,0.142 10 4A 4.791,3.016 5.186,3.159 0.395,0.142 10 4A-90 4.116,1.339 4.278,1.481 0.162,0.142 10 *a 1.51,0.526 1.672,0.668 0.162,0.142 10 *1 4.982,2.649 4.982,3.013 false

Text in Illustration
*1 No. 4 Junction Block - -
*a Front view of wire harness connector
(to No. 4 Junction Block)
- -

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4A-90 - Body ground Ignition switch ON 4.5 to 14 V




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU CIRCUIT)
a.

Disconnect the F78 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-5 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR