Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2013.08
RM1440E _58 Vehicle Interior _056162 SEAT BELT _0274120 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly detects the state of the front seat inner belt assembly RH when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the seat belt warning light in the combination meter assembly blinks. If the front passenger seat belt is fastened, the seat belt warning light turns off.

WIRING DIAGRAM

B355298E02
4.917,2.302 6.802,2.635 1.885,0.333 10 false Combination Meter Assembly 4.927,2.146 5.219,2.323 0.292,0.177 10 false F14 5.354,0.646 5.781,0.813 0.427,0.167 10 false PBKL 5.083,0.542 5.281,0.719 0.198,0.177 10 false 34 2.625,0.781 3.563,1.115 0.938,0.333 10 false Buckle Switch 0.615,1.271 2.365,1.604 1.75,0.333 10 false Occupant Detection Sensor 3.583,0.531 3.729,0.688 0.146,0.156 10 false + 3.781,0.531 3.927,0.688 0.146,0.156 10 false 3 3.583,0.969 3.729,1.125 0.146,0.156 10 false E 3.781,0.958 3.927,1.115 0.146,0.156 10 false 2 2.594,1.844 3.969,2.49 1.375,0.646 10 false Front Seat Inner Belt Assembly RH 2.594,1.677 2.833,1.875 0.24,0.198 10 false N3 0.563,1.656 2.25,2.302 1.688,0.646 10 false Separate Type Front Seat Cushion Pad

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat belt fastened
OFF: Front passenger side seat belt unfastened
Perform the inspection while sitting in the front passenger seat.

OK:

ON or OFF is displayed on the intelligent tester screen according to the front passenger side seat belt condition.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY RH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY RH AND BODY GROUND)
a.

Disconnect the F14 combination meter assembly connector.


b.

Disconnect the N3 front seat inner belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F14-34 (PBKL) - N3-3 (+) Always Below 1 Ω
N3-2 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F14-34 (PBKL) or N3-3 (+) - Body ground Always 10 kΩ or higher




OK

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.

Remove the front seat inner belt assembly RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Inspect the front seat inner belt assembly RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION).



OK

4.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

4.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)
a.

Remove the occupant detection sensor (separate type front seat cushion pad) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).


b.

Inspect the occupant detection sensor (separate type front seat cushion pad) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION).



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)