Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274151 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14A2  Driver Side Solar Sensor Short Circuit  


DESCRIPTION

E132508E02
0.115,0.073 2.948,0.542 2.833,0.469 10 Output Current of Photodiode 0.344,0.75 1.5,1.031 1.156,0.281 10 High 0.365,2.427 1.542,2.698 1.177,0.271 10 Low 0.833,2.708 1.635,3.031 0.802,0.323 10 Weak 2.198,2.688 2.906,3.063 0.708,0.375 10 Strong 0.823,3.063 3.01,3.396 2.188,0.333 10 Strength of Solar Radiation

The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the automatic light control sensor (solar sensor) varies according to the amount of sunlight. When the amount of sunlight increases, the output current increases. As the amount of sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects the output current from the automatic light control sensor (solar sensor).

DTC Code DTC Detection Condition Trouble Area
B14A2 An open or short in the driver side solar sensor circuit.
·

Automatic light control sensor (solar sensor)

·

Harness or connector

·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E196914E13
1.512,0.686 1.898,0.845 0.387,0.159 10 CLTB 0.798,3.204 1.028,3.362 0.230,0.159 10 G2 2.014,1.18 2.142,1.346 0.129,0.167 10 3 2.029,2.677 2.191,2.843 0.161,0.167 10 1 2.014,0.605 2.142,0.772 0.129,0.167 10 6 4.87,2.655 5.047,2.822 0.177,0.167 10 33 1.512,1.275 1.898,1.433 0.387,0.159 10 CLTE 1.607,2.781 1.911,2.940 0.303,0.159 10 TSL 4.83,1.166 5.028,1.332 0.198,0.167 10 22 4.83,0.591 5.024,0.758 0.194,0.167 10 20 5.162,2.774 5.548,2.932 0.387,0.159 10 TSD 5.12,0.686 5.506,0.845 0.387,0.159 10 CLTB 5.12,1.275 5.506,1.433 0.387,0.159 10 CLTE 5.009,1.872 6.666,2.227 1.657,0.355 10 Main Body ECU (Multiplex Network Body ECU) 5.018,1.705 5.318,1.863 0.299,0.159 10 F9 5.101,3.407 6.927,3.747 1.826,0.341 10 Air Conditioning Amplifier Assembly 5.101,3.237 5.407,3.396 0.306,0.159 10 F42 0.792,3.372 2.759,3.747 1.967,0.375 10 Automatic Light Control Sensor (Solar Sensor)

CAUTION / NOTICE / HINT

HINT:
·

If DTC B1244 is output together with other DTCs, troubleshoot DTC B1244 first (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>B1244).

·

If the check is performed in a dark place, DTC B14A2 or B14A3 (solar sensor circuit abnormal) may be stored even though the system is normal.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SOLAR SENSOR)
a.

Use the Data List to check if the automatic light control sensor (solar sensor) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor (D side) Automatic light control sensor (solar sensor) / Min.: 0, Max.: 255 Driver side solar sensor voltage increases as brightness increases Open in the circuit: 0.
Short in the circuit: 255.

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U180999E02
1.427,2.49 0.677,2.823 false 1.885,2.708 2.406,2.854 false 0.104,0.073 0.344,0.292 0.24,0.219 10 false *a 0.417,2.844 0.813,3.01 0.396,0.167 10 false CLTE 2.479,2.792 2.875,2.958 0.396,0.167 10 false CLTB 0.625,1.823 0.844,1.99 0.219,0.167 10 false G2

Disconnect the G2 sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-6 (CLTB) - G2-3 (CLTE) Ignition switch off Below 1 V
G2-6 (CLTB) - G2-3 (CLTE) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Automatic Light Control Sensor [Solar Sensor])



OK

3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)
3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G2 sensor connector.


b.

Disconnect the F42 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-1 (TSL) - F42-33 (TSD) Always Below 1 Ω
G2-1 (TSL) - Body ground Always 10 kΩ or higher




OK

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)
a.
U181004E02
2.781,2.229 2.021,2.229 false 2.781,1.969 2.021,1.969 false 0.521,2 0.729,2.167 0.208,0.167 10 false G2 0.146,0.094 0.406,0.323 0.26,0.229 10 false *a 2.813,2.135 3.198,2.302 0.385,0.167 10 false CLTE 2.813,1.896 3.135,2.063 0.323,0.167 10 false TSL

Remove the automatic light control sensor (solar sensor) with its connector still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-1 (TSL) - G2-3 (CLTE) Ignition switch ON
Sensor subjected to electric light
0.8 to 4.3 V
G2-1 (TSL) - G2-3 (CLTE) Ignition switch ON
Sensor covered with cloth
Below 0.8 V


Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor [Solar Sensor])

NOTICE:

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 1 and the positive (+) lead to terminal 3 of the solar sensor.


HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.

·

As the inspection light is moved away from the sensor, the voltage decreases.





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)
a.

Disconnect the F9 ECU connector.


b.

Disconnect the G2 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-22 (CLTE) - G2-3 (CLTE) Always Below 1 Ω
F9-20 (CLTB) - G2-6 (CLTB) Always Below 1 Ω
F9-22 (CLTE) - Body ground Always 10 kΩ or higher
F9-20 (CLTB) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR