Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the multiplex network master switch, power window regulator motor, harness or connector.


WIRING DIAGRAM

B242536E04
0.333,4.479 0.719,4.479 false 0.719,4.438 0.333,4.438 false 0.719,4.458 0.333,4.458 false 2.75,4.01 4.396,4.615 1.646,0.604 10 false Multiplex Network Master Switch Assembly 4.771,3.75 5.115,3.927 0.344,0.177 10 false I2 1.469,0.615 4.542,0.802 3.073,0.188 10 false Main Body ECU (Multiplex Network Body ECU) 0.271,2.385 1.094,2.573 0.823,0.188 10 false from Battery 0.271,1.125 1.094,1.313 0.823,0.188 10 false from Battery 1.938,1.292 2.552,1.469 0.615,0.177 10 false DOOR D 2.01,2.563 2.469,2.74 0.458,0.177 10 false DOOR 5.406,1.125 5.531,1.302 0.125,0.177 10 false B 5.188,0.979 5.313,1.156 0.125,0.177 10 false 2 5.406,1.667 5.75,1.844 0.344,0.177 10 false GND 5.188,1.531 5.313,1.708 0.125,0.177 10 false 1 5.406,2.302 5.75,2.479 0.344,0.177 10 false UP 5.125,2.156 5.313,2.333 0.188,0.177 10 false 10 5.406,2.719 5.885,2.896 0.479,0.177 10 false DOWN 3.833,2.302 4.063,2.479 0.229,0.177 10 false UP 3.104,2.396 3.333,2.573 0.229,0.177 10 false B 3.104,3.167 3.5,3.344 0.396,0.177 10 false GND 3.583,2.719 4.063,2.896 0.479,0.177 10 false DOWN 5.198,2.604 5.302,2.781 0.104,0.177 10 false 7 4.177,2.156 4.365,2.333 0.188,0.177 10 false 20 4.177,2.604 4.354,2.781 0.177,0.177 10 false 15 2.833,2.323 3.01,2.469 0.177,0.146 10 false 11 2.833,3.063 3.01,3.208 0.177,0.146 10 false 12 0.75,4.375 2.396,4.563 1.646,0.188 10 false : LIN Communication Line 2.74,3.823 3.021,4 0.281,0.177 10 false h1 4.771,3.948 6.76,4.438 1.99,0.49 10 false Front Power Window Regulator Motor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>B2312).

OK:

DTC B2312 is not output.




OK

2.READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

NG

2.READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Use the Data List to check if the multiplex network master switch is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)

NG

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that power window regulator motor operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Driver side power window OFF/UP/DOWN -

OK:

The power window regulator motor operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149798E01
0.329,1.055 0.512,1.211 0.184,0.156 10 h1 1.202,1.353 1.362,1.858 1.362,1.858 1.521,1.858 false 1.057,1.353 0.897,1.858 0.897,1.858 0.738,1.858 false 1.564,1.764 1.918,1.923 0.354,0.159 10 GND 0.584,1.764 0.706,1.923 0.122,0.159 10 B 0.185,0.144 0.361,0.328 0.177,0.184 10 *a

Disconnect the h1 multiplex network master switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h1-11 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
h1-12 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Network Master Switch Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
B216019E10
0.56,0.949 0.729,1.118 0.169,0.170 10 I2 0.178,0.141 0.344,0.300 0.166,0.159 10 *a 1.579,0.79 1.222,0.476 1.222,0.476 1.115,0.476 false 1.871,0.79 2.228,0.476 2.228,0.476 2.335,0.476 false 0.706,0.399 1.053,0.548 0.347,0.149 10 GND 2.374,0.399 2.554,0.673 0.180,0.274 10 B

Disconnect the I2 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I2-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
I2-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH)



OK

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the h1 multiplex network master switch connector.


b.

Disconnect the I2 power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-20 (UP) - I2-10 (UP) Always Below 1 Ω
h1-15 (DOWN) - I2-7 (DOWN) Always Below 1 Ω
h1-20 (UP) - Body ground Always 10 kΩ or higher
h1-15 (DOWN) - Body ground Always 10 kΩ or higher




OK

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
B244063E01
1.768,1.493 1.265,0.457 1.265,0.457 1.058,0.457 false 0.864,0.371 1.029,0.517 0.165,0.147 10 *1 1.881,3.501 2.279,3.27 2.279,3.27 2.382,3.27 false 1.626,3.501 1.228,3.27 1.228,3.27 1.125,3.27 false 2.401,3.182 2.746,3.333 0.345,0.151 10 GND 1.933,3.862 2.33,3.631 2.33,3.631 2.433,3.631 false 2.453,3.543 2.928,3.694 0.475,0.151 10 DOWN 0.992,3.182 1.108,3.333 0.116,0.151 10 B 1.591,3.862 1.194,3.631 1.194,3.631 1.091,3.631 false 0.831,3.543 1.049,3.694 0.218,0.151 10 UP

a.

Remove the front power window regulator motor LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).


b.

Check that the window regulator motor moves smoothly as follows.

NOTICE:
·

Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.


·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor to the door.



OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.


Motor gear rotates clockwise (Up)
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise (Down)


Text in Illustration
*1 Motor Gear
V100135

Clockwise
V100136

Counterclockwise



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH