1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
74811G
2.REMOVE DOOR PULL HANDLE
Using moulding remover D, detach the 4 claws and remove the door pull handle.
Use the same procedure for all door pull handles.
69308
3.REMOVE BACK DOOR LOCK PROTECTOR SUB-ASSEMBLY
Detach the 2 claws and remove the back door lock protector sub-assembly.
74629A
4.REMOVE ASSIST STRAP HOLE COVER
Detach the 2 claws and guide to remove the assist strap hole cover.
74650A
5.REMOVE ASSIST STRAP ASSEMBLY
Remove the bolt and assist strap assembly.
64780A
6.REMOVE BACK DOOR TRIM PANEL ASSEMBLY
Detach the 12 clips by pulling the back door trim panel assembly.
68291
7.REMOVE BACK DOOR GLASS WEATHERSTRIP
Raise the 9 claws of the back door glass weatherstrip and remove the back door glass weatherstrip from the back door trim panel assembly as shown in the illustration.
86160Y
8.REMOVE REAR NO. 2 SPEAKER ASSEMBLY
89222A
9.REMOVE MULTIPLEX NETWORK DOOR ECU
Disconnect the 3 connectors to detach the 2 clamps.
Remove the 3 screws.
Using a clip remover, detach the 2 clips and remove the multiplex network door ECU.
67848C
10.REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER
Remove the No. 2 back door service hole cover.
Remove any remaining tape on the back door side.
67848
11.REMOVE BACK DOOR SERVICE HOLE COVER LH
Detach the clamp and move the wire harness out of the way.
Remove the 5 screws.
Using a clip remover, detach the 2 clips and remove the back door service hole cover LH.
67847
12.REMOVE BACK DOOR SERVICE HOLE COVER RH
Detach the clamp and move the wire harness out of the way.
Remove the 5 screws.
Using a clip remover, detach the 2 clips and remove the back door service hole cover RH.
75816
13.REMOVE BACK DOOR OUTSIDE MOULDING LH
75815
14.REMOVE BACK DOOR OUTSIDE MOULDING RH
76893
15.REMOVE REAR NO. 1 SPOILER COVER
76085
16.REMOVE REAR SPOILER SUB-ASSEMBLY
85241A
17.REMOVE REAR WIPER ARM
85120R
18.REMOVE REAR WIPER MOTOR AND BRACKET ASSEMBLY
67381A
19.REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET
Remove the 3 bolts.
Using a clip remover, detach the 2 clips and remove the No. 1 back window wiper motor bracket.
85345R
20.REMOVE REAR WASHER NOZZLE
85293A
21.REMOVE REAR WIPER STOPPER
Insert a screwdriver into the rear spoiler service hole, detach the claw and remove the liner wiper step RH.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
68275
22.REMOVE BACK DOOR GLASS RUN
Remove the back door glass run.
68131
23.REMOVE BACK DOOR GLASS
Temporarily connect the multiplex network body ECU connectors.
Remove the hole plug.
Connect the cable to the negative (-) battery terminal.
Move the back door glass until the 4 bolts can be seen through the service holes.
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the multiplex network body ECU connectors.
Remove the bolt and disconnect the 2 defogger connectors.
Remove the 4 bolts.
Remove the back door glass as shown in the illustration.
Disconnect the rear window connector.
Disconnect the multiplex network door ECU connector.
68290A
24.REMOVE OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY
69350
25.REMOVE BACK DOOR LOCK ASSEMBLY
69807
26.REMOVE BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY
Disconnect the power window regulator motor assembly LH connector.
Remove the 5 bolts and back door power window regulator sub-assembly.
Remove the back door power window regulator sub-assembly through the service hole.
85720E
27.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69055B
28.REMOVE BACK DOOR LOCK CYLINDER
Disconnect the connector.
Remove the 2 nuts and back door lock cylinder.
Remove the back door lock cylinder through the service hole.
76827A
29.REMOVE NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System)
Detach the 2 claws and remove the No. 2 back door garnish retainer.
76811A
30.REMOVE BACK DOOR OUTSIDE GARNISH
86790D
31.REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)
84840G
32.REMOVE BACK DOOR OPENER SWITCH ASSEMBLY
Disconnect the connector.
Detach the guide.
Remove the 2 screws and back door opener switch assembly.
81270
33.REMOVE LICENSE PLATE LIGHT ASSEMBLY
67281F
34.REMOVE BACK DOOR LOWER STOPPER (for LH Side)
Remove the bolt.
Detach the guide and back door lower stopper.
67281F
35.REMOVE BACK DOOR LOWER STOPPER (for RH Side)
Use the same procedure as for the LH side.
67005B
36.REMOVE BACK DOOR PANEL CUSHION
Remove the 2 back door panel cushions.
68908
37.REMOVE BACK DOOR DAMPER STAY SUB-ASSEMBLY LH
68907
38.REMOVE BACK DOOR DAMPER STAY SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
68961
39.REMOVE BACK DOOR STAY BOLT (for LH Side)
68961
40.REMOVE BACK DOOR STAY BOLT (for RH Side)
Use the same procedure as for the LH side.
68946
41.REMOVE BACK DOOR UPPER DAMPER STAY BRACKET LH
68945
42.REMOVE BACK DOOR UPPER DAMPER STAY BRACKET RH
Use the same procedure as for the LH side.