Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274189 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Wiper does not Operate  


DESCRIPTION

When the windshield wiper switch is operated with the back door power window is fully closed the rear wiper motor operates.

WIRING DIAGRAM

B241220E01
2.613,2.206 4.835,2.562 2.222,0.356 10 F20 Windshield Wiper Switch Assembly 0.596,5.427 2.363,5.954 1.767,0.527 10 V2 Multiplex Network Door ECU (Back Door P/W) 0.134,6.584 0.624,6.584 false 0.627,6.522 0.134,6.522 false 0.133,6.553 0.63,6.553 false 0.685,6.474 2.407,6.637 1.722,0.163 10 : LIN Communication Line 5.236,2.4 7.037,2.775 1.800,0.374 10 Main Body ECU (Multiplex Network Body ECU) 5.735,0.957 6.175,1.122 0.439,0.165 10 RWLS 5.735,1.377 6.178,1.542 0.443,0.165 10 RWC1 2.97,5.413 4.730,5.768 1.760,0.355 10 V1 Rear Wiper Motor Assembly 3.908,0.966 4.196,1.113 0.288,0.147 10 +1R 3.932,1.807 4.196,1.954 0.265,0.147 10 EW 3.89,1.386 4.196,1.534 0.306,0.147 10 C1R 1.59,3.181 1.753,3.344 0.163,0.163 10 W 1.576,3.616 1.739,3.779 0.163,0.163 10 P 1.291,4.036 1.737,4.199 0.445,0.163 10 SGND 1.375,4.456 1.772,4.619 0.397,0.163 10 WIP+ 1.375,4.877 1.741,5.040 0.365,0.163 10 WIP- 3.323,3.181 3.486,3.344 0.163,0.163 10 W 3.323,4.036 3.486,4.199 0.163,0.163 10 E 3.323,3.616 3.768,3.779 0.445,0.163 10 P 3.323,4.456 3.719,4.619 0.397,0.163 10 L 3.323,4.877 3.688,5.040 0.365,0.163 10 E 3.109,3.09 3.238,3.265 0.129,0.174 10 3 1.855,3.09 1.952,3.230 0.097,0.140 10 3 1.855,3.497 1.978,3.636 0.122,0.140 10 4 1.855,3.917 2.067,4.054 0.212,0.137 10 12 1.855,4.337 1.957,4.475 0.101,0.137 10 2 1.855,4.758 1.957,4.895 0.101,0.137 10 5 3.109,3.931 3.238,4.105 0.129,0.174 10 2 3.109,3.511 3.238,3.685 0.129,0.174 10 1 3.109,4.351 3.238,4.526 0.129,0.174 10 5 3.109,4.772 3.238,4.946 0.129,0.174 10 4 5.358,0.953 5.635,1.118 0.277,0.165 10 F10 5.4,1.373 5.611,1.538 0.210,0.165 10 F9 5.419,0.757 5.592,0.922 0.173,0.165 10 17 4.284,0.841 4.402,1.006 0.118,0.165 10 7 4.284,1.261 4.402,1.426 0.118,0.165 10 6 4.284,1.682 4.402,1.847 0.118,0.165 10 2 5.447,1.177 5.550,1.342 0.103,0.165 10 1

CAUTION / NOTICE / HINT

HINT:

Since the wiper and washer system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (WIPER AND BACK DOOR POWER WINDOW POSITION)
a.

Use the Data List to check if the rear wiper and back power window are functioning properly (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).


Back Door P/W
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wiper Retracted Position Rear wiper retracting switch signal / ON or OFF ON: Rear wiper in retracting position
OFF: Rear wiper in other position
-
Wiper Reverse Position Rear wiper reverse position switch signal / ON or OFF ON: Rear wiper in reverse position
OFF: Rear wiper in other position
-
Back Door P/W Status Back door power window position / Open or Close Open: Back door window open
Close: Back door window closed
-

OK:

On the intelligent tester screen, each item changes between ON and OFF according to the above chart.


Result
Result Proceed to
OK A
NG (Rear wiper position) B
NG (Back door power window position) C


A

2.READ VALUE USING INTELLIGENT TESTER (WINDSHIELD WIPER SWITCH)

B

4.CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

C

2.READ VALUE USING INTELLIGENT TESTER (WINDSHIELD WIPER SWITCH)
a.

Use the Data List to check if the rear wiper is functioning properly (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Rear Wiper HI SW Signal Rear wiper HI switch / ON or OFF ON: Rear wiper switch in HI position
OFF: Rear wiper switch not in HI position
-
Rear Wiper LO SW Signal Rear wiper LO switch / ON or OFF ON: Rear wiper switch in LO position
OFF: Rear wiper switch not in LO position
-

OK:

On the intelligent tester screen, each item changes between ON and OFF according to the above chart.



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR WIPER)

NG

6.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR WIPER)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).

Back Door P/W
Tester Display Test Part Control Range Diagnostic Note
Rear Wiper Active Rear wiper motor operation STOP/ACTIVE -

OK:

The rear wiper motor operates normally.




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

8.INSPECT REAR WIPER MOTOR ASSEMBLY
4.CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)
a.

Measure the voltage according to the value(s) in the table below.

U149813E01
3.421,2.784 2.952,2.052 2.952,2.052 2.808,2.052 false 2.689,1.992 2.810,2.141 0.121,0.149 10 P 2.041,2.33 2.463,2.479 0.422,0.149 10 SGND 4.095,0.973 4.442,1.121 0.347,0.149 10 GND 0.494,0.973 0.842,1.121 0.347,0.149 10 GND 3.537,2.812 3.964,2.08 3.964,2.08 4.108,2.08 false 4.132,2.017 4.316,2.166 0.184,0.149 10 W 1.004,0.124 1.820,0.307 0.816,0.184 10 Waveform 1 4.591,0.11 5.406,0.293 0.816,0.184 10 Waveform 2 3.424,2.912 2.608,2.397 2.608,2.397 2.461,2.397 false 3.367,2.166 3.574,2.327 0.207,0.161 10 V2 3.421,2.784 2.952,2.052 2.952,2.052 2.808,2.052 false 2.689,1.992 2.810,2.141 0.121,0.149 10 P 2.041,2.33 2.463,2.479 0.422,0.149 10 SGND 4.095,0.973 4.442,1.121 0.347,0.149 10 GND 0.494,0.973 0.842,1.121 0.347,0.149 10 GND 3.537,2.812 3.964,2.08 3.964,2.08 4.108,2.08 false 4.132,2.017 4.316,2.166 0.184,0.149 10 W 1.004,0.124 1.820,0.307 0.816,0.184 10 Waveform 1 4.591,0.11 5.406,0.293 0.816,0.184 10 Waveform 2 3.424,2.912 2.608,2.397 2.608,2.397 2.461,2.397 false 3.367,2.166 3.574,2.327 0.207,0.161 10 V2

Standard Voltage:
Tester Connection Tool Setting Switch Condition Specified Condition
V2-3 (W) - V2-12 (SGND) 5 V/DIV., 10 ms/DIV. Ignition switch ON and rear wiper switch on (rear wiper reverse position switch off) Pulse generation (See waveform 1)
V2-3 (W) - V2-12 (SGND) 5 V/DIV., 10 ms/DIV. Ignition switch ON and rear wiper switch on (rear wiper reverse position switch on) Pulse generation (See waveform 2)
V2-4 (P) - V2-12 (SGND) 5 V/DIV., 10 ms/DIV. Ignition switch ON and rear wiper switch on (rear wiper retractable position switch off) Pulse generation (See waveform 1)
V2-4 (P) - V2-12 (SGND) 5 V/DIV., 10 ms/DIV. Ignition switch ON and rear wiper switch on (rear wiper retractable position switch on) Pulse generation (See waveform 2)




OK

5.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

5.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the V1 rear wiper motor connector.


b.

Disconnect the V2 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-3 (W) - V2-3 (W) Always Below 1 Ω
V1-1 (P) - V2-4 (P) Always Below 1 Ω
V1-2 (E) - V2-12 (SGND) Always Below 1 Ω
V1-3 (W) - Body ground Always 10 kΩ or higher
V1-1 (P) - Body ground Always 10 kΩ or higher
V1-2 (E) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
a.
U149792E01
2.24,0.332 2.358,0.478 0.118,0.145 10 A 1.346,0.229 1.599,0.371 0.253,0.142 10 EW 2.588,1.77 2.900,1.912 0.312,0.142 10 C1R 1.389,1.767 1.667,1.909 0.277,0.142 10 +1R 2.219,1.243 2.408,1.845 2.408,1.845 2.584,1.845 false 2.085,1.278 1.896,1.845 1.896,1.845 1.72,1.845 false 2.279,0.942 1.819,0.302 1.819,0.302 1.647,0.302 false

Remove the windshield wiper switch (See page Vehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A-6 (C1R) - A-2 (EW) Rear wiper switch LO Below 1 Ω
A-7 (+1R) - A-2 (EW) Rear wiper switch HI Below 1 Ω
A-6 (C1R) - A-2 (EW) Rear wiper switch off 10 kΩ or higher
A-7 (+1R) - A-2 (EW) Rear wiper switch off 10 kΩ or higher
A-6 (C1R) - A-7 (+1R) Rear wiper switch off 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the F20 windshield wiper switch connector.


b.

Disconnect the F9 and F10 main body ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F20-7 (+1R) - F10-17 (RWLS) Always Below 1 Ω
F20-6 (C1R) - F9-1 (RWC1) Always Below 1 Ω
F20-2 (EW) - Body ground Always Below 1 Ω
F20-7 (+1R) - Body ground Always 10 kΩ or higher
F20-6 (C1R) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR WIPER MOTOR ASSEMBLY
a.
E196889E07
2.369,1.638 2.579,1.794 0.210,0.156 10 E 0.963,1.655 1.083,1.811 0.119,0.156 10 L 1.846,1.287 2.207,1.737 2.207,1.737 2.344,1.737 false 1.588,1.287 1.227,1.737 1.227,1.737 1.09,1.737 false

Remove the rear wiper motor (See page Vehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL).


b.

Apply battery voltage to the rear wiper motor and check the operation of the rear wiper motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 5 (L)
Battery negative (-) → 4 (E)
Rear wiper motor operation is normal




OK

9.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the V1 rear wiper motor connector.


b.

Disconnect the V2 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-5 (L) - V2-2 (WIP+) Always Below 1 Ω
V1-4 (E) - V2-5 (WIP-) Always Below 1 Ω
V1-5 (L) - Body ground Always 10 kΩ or higher
V1-4 (E) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR