Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

DTC    P101D    A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON

DTC    P103D    A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. When one of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

  4. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


    A164715E09


DTC No.
DTC Detection Condition
Trouble Area
P0031
P0051
Air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
  1. Open in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (sensor 1)
  3. No. 1 integration relay
  4. ECM
P0032
P0052
Air fuel ratio sensor heater current failure (1 trip detection logic).
  1. Short in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (sensor 1)
  3. No. 1 integration relay
  4. ECM
P101D
P103D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
ECM

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0031: Air fuel ratio sensor heater (bank 1) open/short (Low electrical current)
P0032: Air fuel ratio sensor heater (bank 1) open/short (High electrical current)
P0051: Air fuel ratio sensor heater (bank 2) open/short (Low electrical current)
P0052: Air fuel ratio sensor heater (bank 2) open/short (High electrical current)
P101D: Air fuel ratio sensor heater (for Bank 1) performance
P103D: Air fuel ratio sensor heater (for Bank 2) performance
Required Sensors/Components (Main)
Air fuel ratio sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
11 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0031 and P0051 
Monitor runs whenever following DTCs not stored
P101D, P103D (Air fuel ratio sensor heater)
Battery voltage
10.5 V or higher
Time after heater ON
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater duty-cycle
10% or more

P0032 and P0052 
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or higher
Time after heater ON
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater duty-cycle
More than 0%

P101D and P103D 
Monitor runs whenever following DTCs not stored
P0031, P0051 (Air fuel ratio sensor heater)
Battery voltage
10.5 V or higher
Time after heater ON
5 seconds or more
Active heater OFF control
Not operating
Active heater ON control
Not operating
Air fuel ratio sensor heater duty-cycle
10 to 60%
Air fuel ratio sensor heater ON current
0.8 A or higher

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051 
Air fuel ratio sensor heater current
Below 0.8 A

P0032 and P0052 
Air fuel ratio sensor heater output
ON
Hybrid IC high current limiter monitor
Fail

P101D and P103D 
Air fuel ratio sensor heater OFF current
Higher than 11 A
Active heater OFF control for stuck ON malfunction
Operating
Hybrid IC high current limiter monitor
Fail

COMPONENT OPERATING RANGE


Air fuel ratio sensor heater current
0.8 A or higher

CONFIRMATION DRIVING PATTERN


A198819E32

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream ON.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click here). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor .



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
A150242E34
  1. Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B26-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    B27-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    Bank 1
    *B
    Bank 2
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B26-1 (HA1A) - B39-17 (HA1A)
    Always
    Below 1 Ω
    B27-1 (HA2A) - B39-19 (HA2A)
    Always
    Below 1 Ω
    B26-1 (HA1A) or B39-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B27-1 (HA2A) or B39-19 (HA2A) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the output pending DTCs using the Techstream.

    Result 
    Display (DTC Output)
    Proceed to
    No pending DTC is output
    A
    Pending DTC P0031, P0032, P0051, P0052, P101D or P103D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.INSPECT NO. 1 INTEGRATION RELAY (A/F)
  1. Inspect the No. 1 integration relay (A/F) .



NG
REPLACE NO. 1 INTEGRATION RELAY
OK


6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (A/F) - A/F SENSOR AND BODY GROUND)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B26-2 (+B) - 1D-8
    Always
    Below 1 Ω
    B27-2 (+B) - 1D-8
    Always
    Below 1 Ω
    1D-7 - Body ground
    Always
    Below 1 Ω
    B26-2 (+B) or 1D-8 - Body ground
    Always
    10 kΩ or higher
    B27-2 (+B) or 1D-8 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)