Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the multiplex network master switch, power window regulator motor, harness or connector.

WIRING DIAGRAM


B242536E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

1.CHECK FOR DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC B2312 (Click here)
OK


2.READ VALUE USING TECHSTREAM (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
  1. Use the Data List to check if the multiplex network master switch is functioning properly (Click here).

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver side power window manual up signal / ON or OFF
    ON: Driver side power window manual up switch operated
    OFF: Driver side power window switch not operated
    -
    D Door P/W Down SW
    Driver side power window manual down signal / ON or OFF
    ON: Driver side power window manual down switch operated
    OFF: Driver side power window switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (POWER WINDOW)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that power window regulator motor operates (Click here).

    D-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Driver side power window
    OFF/UP/DOWN
    -

    OK:
    The power window regulator motor operates normally.



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)


    B242663E01
  1. Disconnect the h1 multiplex network master switch connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    h1-11 (B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-12 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Network Master Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)


    B216019E10
  1. Disconnect the I2 power window regulator motor connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I2-2 (B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I2-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Power Window Regulator Motor Assembly LH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the h1 multiplex network master switch connector.

  1. Disconnect the I2 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-20 (UP) - I2-10 (UP)
    Always
    Below 1 Ω
    h1-15 (DOWN) - I2-7 (DOWN)
    Always
    Below 1 Ω
    h1-20 (UP) - Body ground
    Always
    10 kΩ or higher
    h1-15 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
B244063E01
  1. Remove the front power window regulator motor LH (Click here).

  1. Check that the window regulator motor moves smoothly as follows.

    NOTICE:
    1. Do not apply positive (+) battery voltage to any terminal other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.
    1. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor to the door.


    OK:

    Measurement Condition
    Specified Condition
    1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.
    Motor gear rotates clockwise (Up)
    1. Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.
    Motor gear rotates counterclockwise (Down)

    Text in Illustration 
    *1
    Motor Gear
    V100135
    Clockwise
    V100136
    Counterclockwise



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)