Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the power window regulator switch, front power window regulator motor, harness or connector.

WIRING DIAGRAM


B242537E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

1.CHECK FOR DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC B2312 (Click here)
OK


2.READ VALUE USING TECHSTREAM (POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the front power window regulator motor is functioning properly (Click here).

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Up SW
    Front passenger side power window manual up signal / ON or OFF
    ON: Front passenger side power window manual up switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual down signal / ON or OFF
    ON: Front passenger side power window manual down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (POWER WINDOW)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that power window regulator motor operates (Click here).

    P-Door Motor 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Passenger side power window
    OFF/UP/DOWN
    -

    OK:
    The power window regulator motor operates normally.



NG
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B215963E16
  1. Remove the power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual up operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual down operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BODY GROUND)


    B216018E05
  1. Disconnect the g1 power window regulator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    g1-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Window Regulator Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
  1. Disconnect the g1 power window regulator switch connector.

  1. Disconnect the H2 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    g1-6 (UP) - H2-10 (UP)
    Always
    Below 1 Ω
    g1-7 (DOWN) - H2-7 (DOWN)
    Always
    Below 1 Ω
    g1-6 (UP) - Body ground
    Always
    10 kΩ or higher
    g1-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)


    B216019E05
  1. Disconnect the H2 power window regulator motor connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H2-2 (B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H2-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Front Power Window Regulator Motor Assembly RH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)