Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1422    Master Cylinder Pressure Sensor Zero Point High Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1421, C1423 and C1424 .

DTC Code
DTC Detection Condition
Trouble Area
C1422
When the stop light switch assembly is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
  1. Stop light switch assembly
  2. Stop light switch circuit
  3. Master cylinder pressure sensor circuit
  4. Master cylinder solenoid (Master cylinder pressure sensor)

WIRING DIAGRAM

Refer to DTC C1380 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

HINT:
When DTC C1425 is output together with DTC C1422, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    On
    Brake pedal released
    Off



NG
INSPECT STOP LIGHT CIRCUIT (Click here)
OK


2.READ VALUE USING TECHSTREAM (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly/ ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light condition observed on the Techstream changes according to brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to brake pedal operation.



NG
Go to step 5
OK


3.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
  1. Turn the ignition switch off.

  1. Check the brake pedal height and stop light switch assembly installation (Click here).

    OK:
    The brake pedal height and stop light switch assembly installation are normal.



NG
ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH (Click here)
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC C1422 is not output
    A
    DTC C1422 is output
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK TERMINAL VOLTAGE (STP)


    C214161E24
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the A6 skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-7 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A6-7 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)