Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL

PARKING BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL PARKING PEDAL PAD
  1. Install the parking pedal pad.



2. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY
  1. Temporarily install the No. 1 parking brake cable assembly with the adjusting nut and lock nut.



  1. Install the No. 1 parking brake cable assembly with the 4 nuts and 3 bolts.


    C215294E01

    Torque:
    for nut A:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
    for bolt B:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C217118
  1. Pass the No. 1 parking brake cable through the parking brake pedal.

  1. Install the clip.

  1. Bend the parking brake pedal claw.

  1. Temporarily install the adjusting nut and lock nut to the No. 1 parking brake cable.



3. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY
  1. Install the parking brake control pedal assembly with the 3 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Connect the parking brake switch connector.



4. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
  1. Transmission type A750F:
    Install the transmission floor shift assembly .

  1. Transmission type A750E:
    Install the transmission floor shift assembly .



5. INSTALL AIRBAG SENSOR ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Install the airbag sensor with the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that the airbag sensor is not loose.

  1. Connect the connector.



6. INSTALL YAW RATE AND ACCELERATION SENSOR
  1. Connect the connector, and then attach the clamp to the hole of the sensor bracket.

    NOTICE:
    Securely connect the connector.

  1. Install the yaw rate and acceleration sensor with the 2 bolts.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. If the sensor is dropped, replace it.
    2. Make sure the bracket rotation stopper touches the installation position.
    3. Make sure that the sensor is oriented correctly.
    4. When installing the sensor, make sure to avoid impacts to the sensor.



7. INSTALL TIRE PRESSURE WARNING ECU
  1. Install the tire pressure warning ECU with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



8. INSTALL TURN SIGNAL FLASHER ASSEMBLY
  1. Install the turn signal flasher assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



9. INSTALL REAR CONSOLE BOX ASSEMBLY
  1. Install the rear console box assembly (Click here).



10. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
  1. Install the lower No. 1 instrument panel airbag assembly (Click here).



11. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL
  1. Remove the lower instrument panel finish panel sub-assembly (Click here).

  1. Completely release the parking brake pedal.



    C215935E01
  1. Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  1. Temporarily install the hub nuts to the hub bolts.

    HINT:
    Securely install the hub nuts to the rear disc.



    D028126E08
  1. Turn the shoe adjuster so that it expands until the disc locks.
    Text in Illustration 
    V100135
    Shoe Adjuster Contracts
    V100136
    Shoe Adjuster Expands

  1. Turn the shoe adjuster so that it contracts until the disc can rotate smoothly.

    Standard:
    8 notches

  1. Check that there is no brake drag against the shoe.



    C217141E02
  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Standard parking brake pedal travel:
    5 to 7 clicks at 294 N (30 kgf, 66 lbf)

    Text in Illustration 
    *1
    Adjusting Nut

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.



  1. Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable as follows.



      C215295
    1. Loosen the No. 1 parking brake cable lock nut.

    2. Turn the No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

      Standard parking brake pedal travel:
      5 to 7 clicks at 294 N (30 kgf, 66 lbf)

    3. Tighten the No. 1 parking brake cable lock nut.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      Pay attention that the adjustment nut does not rotate together with the lock nut during tightening.

    4. Depress and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.

      Standard:
      5 to 7 notches

      If the result is not as specified, adjust the parking brake pedal travel again.

  1. Remove the hub nuts from the hub bolts.

  1. Install the lower instrument panel finish panel sub-assembly (Click here).

  1. When operating the parking brake lever, check that the brake warning light comes on.

    OK:
    The brake warning light always illuminates at the first click.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).