Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Speaker Circuit

for Preparation Click here


DESCRIPTION

  1. If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)*1 or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.
  1. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


for 9 Speakers

E283191E01


E283189E01


for 8 Speakers

E283190E01


INSPECTION PROCEDURE

1.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    for 9 Speakers
    A
    for 8 Speakers
    B



B
Go to step 9
A


2.CHECK HARNESS AND CONNECTOR (for 9 Speakers)
  1. Disconnect the connectors from the N12 and N13 stereo component amplifier assembly, F39 DCM (telematics transceiver)*1 and speakers.

    1. *1: w/ Manual (SOS) Switch

  1. w/ Manual (SOS) Switch

    1. Measure the resistance between the stereo component amplifier assembly and the DCM (telematics transceiver) to check for an open circuit in the wire harness.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N12-10 (FR+) - F39-2 (SPI+)
      Always
      Below 1 Ω
      N12-9 (FR-) - F39-3 (SPI-)
      Always
      Below 1 Ω

    2. Measure the resistance between the front No. 1 speaker assembly RH and the DCM (telematics transceiver) to check for an open circuit in the wire harness.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H1-1 - F39-5 (SPO+)
      Always
      Below 1 Ω
      H1-2 - F39-6 (SPO-)
      Always
      Below 1 Ω

  1. w/o Manual (SOS) Switch

    1. Measure the resistance between the front No. 1 speaker assembly RH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N12-10 (FR+) - H1-1
      Always
      Below 1 Ω
      N12-9 (FR-) - H1-2
      Always
      Below 1 Ω

  1. Measure the resistance between the front No. 1 speaker assembly LH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N12-3 (FL+) - I1-1
    Always
    Below 1 Ω
    N12-8 (FL-) - I1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N12-2 (TWR+) - G22-4
    Always
    Below 1 Ω
    N12-7 (TWR-) - G22-3
    Always
    Below 1 Ω
    N12-1 (TWL+) - G15-4
    Always
    Below 1 Ω
    N12-6 (TWL-) - G15-3
    Always
    Below 1 Ω

  1. Measure the resistance between the rear speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N12-5 (RR+) - J1-1
    Always
    Below 1 Ω
    N12-12 (RR-) - J1-2
    Always
    Below 1 Ω
    N12-4 (RL+) - K1-1
    Always
    Below 1 Ω
    N12-11 (RL-) - K1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N13-4 (R-R+) - W5-1
    Always
    Below 1 Ω
    N13-10 (R-R-) - W5-2
    Always
    Below 1 Ω
    N13-3 (R-L+) - W6-1
    Always
    Below 1 Ω
    N13-9 (R-L-) - W6-2
    Always
    Below 1 Ω

  1. Measure the resistance between the No. 1 speaker with box assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N13-1 (WF2+) - N15-2 (WF2+)
    Always
    Below 1 Ω
    N13-5 (WF2-) - N15-4 (WF2-)
    Always
    Below 1 Ω
    N13-2 (WF1+) - N15-1 (WF1+)
    Always
    Below 1 Ω
    N13-6 (WF1-) - N15-3 (WF1-)
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N12-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    N12-9 (FR-) - Body ground
    Always
    10 kΩ or higher
    N12-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    N12-8 (FL-) - Body ground
    Always
    10 kΩ or higher
    N12-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    N12-7 (TWR-) - Body ground
    Always
    10 kΩ or higher
    N12-1 (TWL+) - Body ground
    Always
    10 kΩ or higher
    N12-6 (TWL-) - Body ground
    Always
    10 kΩ or higher
    N12-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    N12-11 (RL-) - Body ground
    Always
    10 kΩ or higher
    N12-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    N12-12 (RR-) - Body ground
    Always
    10 kΩ or higher
    N13-3 (R-L+) - Body ground
    Always
    10 kΩ or higher
    N13-9 (R-L-) - Body ground
    Always
    10 kΩ or higher
    N13-4 (R-R+) - Body ground
    Always
    10 kΩ or higher
    N13-10 (R-R-) - Body ground
    Always
    10 kΩ or higher
    N13-1 (WF2+) - Body ground
    Always
    10 kΩ or higher
    N13-5 (WF2-) - Body ground
    Always
    10 kΩ or higher
    N13-2 (WF1+) - Body ground
    Always
    10 kΩ or higher
    N13-6 (WF1-) - Body ground
    Always
    10 kΩ or higher

  1. w/ Manual (SOS) Switch
    Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    F39-6 (SPO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY (for 9 Speakers)


    E144966E49
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H1-1 - H1-2
    Always
    1.4 to 2.2 Ω
    I1-1 - I1-2
    Always
    1.4 to 2.2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (for 9 Speakers)
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

HINT:
  1. Connect all the connectors to the front No. 2 speaker assemblies.
  2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
  3. Perform the above inspection on both LH and RH sides.



NG
Go to step 5
OK

END 

5.REPLACE REAR SPEAKER ASSEMBLY (for 9 Speakers)
  1. Replace the rear speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

HINT:
  1. Connect all the connectors to the rear speaker assemblies.
  2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
  3. Perform the above inspection on both LH and RH sides.



NG
Go to step 6
OK

END 

6.REPLACE REAR NO. 2 SPEAKER ASSEMBLY (for 9 Speakers)
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

HINT:
  1. Connect all the connectors to the rear No. 2 speaker assemblies.
  2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
  3. Perform the above inspection on both LH and RH sides.



NG
Go to step 7
OK

END 

7.INSPECT NO. 1 SPEAKER WITH BOX ASSEMBLY (for 9 Speakers)


    E144969E63
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N15-1 (WF1+) - N15-3 (WF1-)
    Always
    1.6 to 2.4 Ω
    N15-2 (WF2+) - N15-4 (WF2-)
    Always
    1.6 to 2.4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Speaker with Box Assembly)

Result:
Condition
Proceed to
OK (w/ Manual (SOS) Switch)
A
OK (w/o Manual (SOS) Switch)
B
NG
C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE NO. 1 SPEAKER WITH BOX ASSEMBLY (Click here)
A


8.INSPECT DCM (TELEMATICS TRANSCEIVER)
  1. Disconnect the F39 DCM (Telematics transceiver) connector.



    E169849E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-2 (SPI+) - F39-5 (SPO+)
    Always
    Below 1 Ω
    F39-3 (SPI-) - F39-6 (SPO-)
    Always
    Below 1 Ω
    F39-2 (SPI+) - F39-3 (SPI-)
    Always
    10 kΩ or higher
    F39-5 (SPO+) - F39-6 (SPO-)
    Always
    10 kΩ or higher
    F39-2 (SPI+) - Body ground
    Always
    10 kΩ or higher
    F39-3 (SPI-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (DCM (Telematics Transceiver))



NG
REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

9.CHECK HARNESS AND CONNECTOR (for 8 Speakers)
  1. Disconnect the connectors from the G6 and G5 navigation receiver assembly and speakers.

  1. Measure the resistance between the navigation receiver assembly and the front No. 2 speaker assembles to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-1 (FR+) - G10-1 (+)
    Always
    Below 1 Ω
    G6-5 (FR-) - G10-3 (-)
    Always
    Below 1 Ω
    G6-2 (FL+) - G1-1 (+)
    Always
    Below 1 Ω
    G6-6 (FL-) - G1-3 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 1 speaker assembles and the front No. 2 speaker assembles to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H1-1 - G10-2 (TWR+)
    Always
    Below 1 Ω
    H1-2 - G10-4 (TWR-)
    Always
    Below 1 Ω
    I1-1 - G1-2 (TWL+)
    Always
    Below 1 Ω
    I1-2 - G1-4 (TWL-)
    Always
    Below 1 Ω

  1. Measure the resistance between the navigation receiver assembly, rear speaker assembly RH and rear No. 2 speaker assembly RH to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G5-1 (RR+) - J1-1
    Always
    Below 1 Ω
    G5-3 (RR-) - W5-2
    Always
    Below 1 Ω
    W5-1 - J1-2
    Always
    Below 1 Ω

  1. Measure the resistance between the navigation receiver assembly, rear speaker assembly LH and rear No. 2 speaker assembly LH to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G5-2 (RL+) - K1-1
    Always
    Below 1 Ω
    G5-6 (RL-) - W6-2
    Always
    Below 1 Ω
    W6-1 - K1-2
    Always
    Below 1 Ω

  1. Measure the resistance between the navigation receiver assembly, speaker assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    G6-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    G6-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    G6-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    G5-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    G5-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    G5-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    G5-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    G10-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    G10-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    G1-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    G1-4 (TWR-) - Body ground
    Always
    10 kΩ or higher
    W6-1 - Body ground
    Always
    10 kΩ or higher
    W5-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY (for 8 Speakers)


    E144966E49
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H1-1 - H1-2
    Always
    4 Ω
    I1-1 - I1-2
    Always
    4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


11.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (for 8 Speakers)
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

HINT:
  1. Connect all the connectors to the front No. 2 speaker assemblies.
  2. If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
  3. Perform the above inspection on both LH and RH sides.



NG
Go to step 12
OK

END 

12.INSPECT REAR SPEAKER ASSEMBLY (for 8 Speakers)


    E144966E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J1-1- J1-2
    Always
    4 Ω
    K1-1 - K1-2
    Always
    4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


13.INSPECT REAR NO. 2 SPEAKER ASSEMBLY (for 8 Speakers)


    E144966E52
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W5-1 - W5-2
    Always
    4 Ω
    W6-1 - W6-2
    Always
    4 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear No. 2 Speaker Assembly)
    *b
    for RH
    *c
    for LH



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)