Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1790    Center Airbag Sensor Assembly Communication Circuit Malfunction

for Preparation Click here


DESCRIPTION

The center airbag sensor communication circuit consists of the occupant classification ECU and center airbag sensor.
DTC B1790 is stored when a malfunction is detected in the center airbag sensor communication circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1790
One of the following conditions is met:
  1. Occupant classification ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the center airbag sensor communication circuit for 2 seconds.
  2. Center airbag sensor malfunction.
  3. Occupant classification ECU malfunction.
  1. Floor wire
  2. Front seat wire RH
  3. Occupant classification ECU
  4. Center airbag sensor

HINT:
  1. When DTC B1630/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1790 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


C213893E01


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and center airbag sensor.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3.CHECK CONNECTOR
  1. Disconnect the connectors from the center airbag sensor and occupant classification ECU.

  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE HARNESS OR CONNECTOR
OK


4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT


    C213888E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a9-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    a9-4 (FSR-) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a9-8 (FSR+) - a9-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a9-8 (FSR+) - a9-4 (FSR-)
    Always
    1 MΩ or higher
    a9-8 (FSR+) - Body ground
    a9-4 (FSR-) - Body ground

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor
    *3
    Service Wire
    *4
    Connector E
    *5
    Connector B
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *b
    Front view of wire harness connector
    (to Center Airbag Sensor)



NG
Go to step 10
OK


5.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


7.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


8.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT


9.CHECK FOR DTC
  1. Clear the DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1790 is not output.

    HINT:
    DTCs other than DTC B1790 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

10.CHECK FRONT SEAT WIRE RH


    C213889E02
  1. Disconnect the front seat wire RH connector from the floor wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Na2-1 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    Na2-4 (FSR-) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the connector from the occupant classification ECU.

  1. Using a service wire, connect terminals 8 (FSR+) and 4 (FSR-) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Na2-1 (FSR+) - Na2-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Na2-1 (FSR+) - Na2-4 (FSR-)
    Always
    1 MΩ or higher
    Na2-1 (FSR+) - Body ground
    Na2-4 (FSR-) - Body ground

    Text in Illustration 
    *1
    Front Seat Wire RH
    *2
    Floor Wire
    *3
    Occupant Classification ECU
    *4
    Center Airbag Sensor
    *5
    Service Wire
    *6
    Connector E
    *7
    Connector D
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *b
    Front view of wire harness connector
    (to Front Seat Wire RH)



NG
REPLACE FRONT SEAT WIRE RH
OK

REPLACE FLOOR WIRE