Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Attach the 2 claws to install the instrument panel reinforcement assembly.

  1. Install the 5 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY


  1. Install the instrument panel reinforcement assembly with air conditioning unit assembly.

    1. Install the bolts, nuts and instrument panel reinforcement assembly with air conditioning assembly.

    2. Using a 12 mm hexagon wrench, tighten the 2 collars.

    3. Using a T40 "TORX" socket, install the 5 "TORX" bolts.

      Torque:
      27 N*m{ 275 kgf*cm , 20 ft.*lbf }



    4. Install the 5 caps.


      E197386E01



  1. Attach the clamps and connect the connectors to the wire harness.


    E197385



3. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY
  1. Attach the 3 claws to install the duct.



4. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
  1. Attach the 3 claws to install the air duct.

  1. Install the screw.



5. INSTALL INSTRUMENT PANEL BRACE MOUNTING BRACKET LH
  1. Install the instrument panel brace mounting bracket LH with the 2 nuts and bolt.



6. INSTALL INSTRUMENT PANEL BRACE MOUNTING BRACKET RH
  1. Install the instrument panel brace mounting bracket RH with the 2 nuts and bolt.



7. INSTALL NO. 1 CONSOLE BOX DUCT
  1. Install the No. 1 console box duct with the clip.



8. INSTALL REAR NO. 3 AIR DUCT
  1. Attach the 3 clamps and 4 claws to install the rear No. 3 air duct.



9. INSTALL REAR NO. 1 AIR DUCT
  1. Attach the 3 clamps and 4 claws to install the rear No. 1 air duct.



10. INSTALL FRONT FLOOR CARPET ASSEMBLY
  1. Install the front floor carpet assembly.



11. INSTALL FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    Install the front seat assembly LH (Click here).

  1. for Power Seat:
    Install the front seat assembly LH (Click here).



12. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.

  1. for Manual Seat:
    Install the front seat assembly RH (Click here).

  1. for Power Seat:
    Install the front seat assembly RH (Click here).



13. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly (Click here).



14. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel sub-assembly (Click here).



15. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Install the windshield wiper motor assembly (Click here).



16. CONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE


    E236474E01
  1. Connect the 2 heater water hoses.
    Text in Illustration 
    *a
    Green Marking
    *b
    Blue Marking

  1. Using pliers, grip the claws of the clips and slide the 2 clips.



17. CONNECT AIR CONDITIONING TUBE ASSEMBLY


E197374
  1. Install the grommet.

  1. Install the 2 new O-rings to the air conditioning tube assembly.

    Compressor oil:
    ND-OIL 8 or equivalent



    E112921E02
  1. Connect the air conditioning tube assembly with the piping clamp.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    After connecting the tube, check that the claw of the piping clamp is attached.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



19. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).



20. ADD ENGINE COOLANT
  1. Add engine coolant .



21. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    550 +/-30 g (19.3 +/-1.0 oz.)



    I037365E19

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant and overheats.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear.



22. WARM UP ENGINE
  1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor by turning the A/C switch on after removing and installing the cooler refrigerant lines (including the compressor) to prevent damage to the compressor.



23. CHECK FOR ENGINE COOLANT LEAK
  1. Check for engine coolant leak .



24. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When the compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).



    I042222E34
  1. Using a halogen leak detector, check the refrigerant line for leakage.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Check for Leakage

  1. If a gas leak from the drain hose is not detected, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.