Home › Drivetrain ยท A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.



    A224743
  1. Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.



3. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover assembly.



4. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 4 clips and front fender apron seal RH.



5. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Remove the 5 clips and front No. 1 fender apron to frame seal RH.



6. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



7. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft (Click here).



8. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe (Click here).



9. REMOVE MANIFOLD STAY


C171485
  1. Remove the 3 bolts and stay.



10. REMOVE NO. 2 MANIFOLD STAY


C171486
  1. Remove the 3 bolts and stay.



11. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C214587
  1. Remove the nut and clip, and disconnect the transmission control cable from the transmission.



12. DISCONNECT NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE


C213421E05
  1. Remove the 2 bolts to open the 2 No. 2 flexible hose clamps.

  1. Using a union nut wrench, disconnect the inlet tube and outlet tube from each oil cooler tube union.



13. REMOVE STARTER ASSEMBLY
  1. Remove the starter (Click here).



14. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


C157016E01
  1. Remove the flywheel housing side cover.



    C157017E01
  1. Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.



15. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C112848
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.



16. REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH (for X-Runner)


C216979
  1. Remove the 8 bolts and front suspension member bracket LH and RH.



17. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


C216980
  1. Remove the 4 bolts of the rear engine mounting insulator.



    C216981
  1. Remove the 4 nuts, 4 bolts and frame crossmember.



18. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


C216982
  1. Remove the bolt and rear engine mounting heat insulator.

  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.



19. DISCONNECT WIRE HARNESS AND CONNECTOR


    C112849
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.



  1. Disconnect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.



    C216983E01

  1. Detach the 2 connector clamps and 4 harness clamps, and disconnect the wire harness.



20. DISCONNECT BREATHER PLUG HOSE


C216991
  1. Disconnect the breather plug hose from the engine side.



21. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


C157018
  1. Remove the 9 bolts and automatic transmission.

    NOTICE:
    Do not use excess force when prying the transmission assembly.



22. REMOVE HARNESS CLAMP BRACKET


C216984
  1. Remove the 4 bolts and 4 harness clamp brackets.



23. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


C111232
  1. Remove the 2 bolts and transmission control cable bracket.



24. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


25. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch (Click here).