Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P050A    Cold Start Idle Air Control System Performance

for Preparation Click here


DESCRIPTION

The Electronic Throttle Control System (ETCS) controls the engine idling speed. The ETCS operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idling speed.
In addition, the ECM retards the ignition timing and the ETCS increases the intake air amount to quickly increase the catalyst temperature at cold start to reduce emissions.

DTC No.
DTC Detection Condition
Trouble Area
P050A
Accumulated intake air amount during 10 seconds of idling after a cold start is less than the threshold (2 trip detection logic).
  1. Throttle body with motor assembly
  2. Mass air flow meter
  3. Air induction system
  4. PCV hose connections
  5. VVT system
  6. Air cleaner filter element
  7. ECM
  8. Wire harness or connector

MONITOR DESCRIPTION


A153341E15

The ECM monitors the intake air amount during idling, and the ignition timing.
When the engine coolant temperature is between -10°C and 50°C (14°F and 122°F), the ECM calculates the idling intake air amount for 10 seconds, beginning 3 seconds after the engine starts.
When the accumulated amount is below the threshold, the ECM interprets this as a malfunction in the Idle Speed Control (ISC) system at cold start.
The ECM also monitors the ignition timing at cold start and determines it to be incorrect when it is advanced to the same value as a warm engine for 5 seconds or more of the 10 second monitoring period.
Example:
P050A is detected when all conditions below are met (2 trip detection logic).
  1. The engine coolant temperature is between -10°C and 50°C (14°F and 122°F) when the engine starts.
  2. The engine idles for 13 seconds after engine start.
  3. The accumulated intake air amount is below the threshold.
The ECM stores the DTC and illuminates the MIL 13 seconds after the engine is next started.

NOTICE:
When the cable is disconnected from the negative battery terminal during inspection or repairs, the ISC learned values are cleared. ISC learning must be performed by warming up the engine and idling for 5 minutes with the engine coolant temperature at 75°C (167°F) or higher because DTCs cannot be detected with the ISC learned values cleared.


MONITOR STRATEGY


Related DTCs
P050A: Idle speed control problem at cold
Required Sensors/Components (Main)
Mass air flow meter
Required Sensors/Components (Related)
Engine coolant temperature sensor, Throttle position sensor, Vehicle speed sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
P219A, P219B (Air-Fuel Ratio Imbalance)
Battery voltage
8 V or higher
Time after engine start
3 seconds or more
Starter
OFF
Engine coolant temperature at engine start
-10°C (14°F) or higher
Engine coolant temperature
-10 to 50°C (14 to 122°F)
Engine idling time
3 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 3 km/h (1.875 mph)
Time after shift position changed
1 second or more
Atmospheric pressure
76 kPa (570 mmHg) or higher

TYPICAL MALFUNCTION THRESHOLDS


Accumulated air flow amount
Varies with ECT (Example: Less than 44 g)

CONFIRMATION DRIVING PATTERN


A198821E07

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
  7. Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C.
  8. Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.
  9. Idle the engine for 1 minute or more [B].
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  11. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P050A.
  14. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [C] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0102 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P050A
    A
    P050A and other DTCs
    B

    HINT:
    If any DTCs other than P050A are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.

  1. Read the values displayed on the Techstream.

  1. Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

    OK:
    Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.



NG
Go to step 5
OK


3.INSPECT THROTTLE VALVE
  1. Check for deposits around the throttle valve, and check the throttle valve condition.

    OK:
    No deposits around throttle valve and throttle valve moves smoothly.



OK
Go to step 14

NG
Go to step 4

4.REPAIR OR REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
  1. Repair or replace the throttle body (Click here).



NEXT
Go to step 14

5.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

OK:
PCV hose is connected correctly and is not damaged.



NG
Go to step 10
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage.

    OK:
    No leakage from air induction system.



NG
Go to step 11
OK


7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

    OK:
    Air cleaner filter element is not excessively contaminated with dirt or oil.



NG
Go to step 12
OK


8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve using the Techstream.

    OK:

    Tester Operation
    Specified Condition
    0% (OFF)
    Normal engine speed
    127% (ON)
    Engine idles roughly or stalls
    (soon after camshaft timing oil control valve switched from OFF to ON)

HINT:
Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2] (Click here).



NG
Go to step 13
OK


9.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 13.8 g/sec. and 17.3 g/sec. (shift lever: N; A/C: Off).



OK
Go to step 14

NG
Go to step 15

10.REPAIR OR REPLACE PCV HOSE
  1. Repair or replace the PCV hose.



NEXT
Go to step 14

11.REPAIR OR REPLACE AIR INDUCTION SYSTEM
  1. Repair or replace the air induction system.



NEXT
Go to step 14

12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Replace air cleaner filter element sub-assembly.



NEXT
Go to step 14

13.CHECK AND REPAIR VVT SYSTEM
  1. Check and repair the VVT system.

    HINT:
    Refer to DTC P0011 Inspection Procedure (Click here).


NEXT


14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NOTICE:
In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050A.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL (DTC P050A is output)
    A
    NORMAL (DTC is not output)
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050A.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL (DTC P050A is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-5 (VG) - B37-14 (VG)
    Always
    Below 1 Ω
    B35-4 (E2G) - B37-13 (E2G)
    Always
    Below 1 Ω
    B35-5 (VG) or B37-14 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)
OK


18.REPAIR OR REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    If the results of the inspections performed in steps 16 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NOTICE:
In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P050A.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P050A is output)
    B



B
REPLACE ECM (Click here)
A

END