Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > Back Door Entry Unlock Function does not Operate

for Preparation Click here


DESCRIPTION

  1. If the back door entry unlock function using the back door opener switch assembly does not operate but the back door lock function operates, one of the following may be malfunctioning: 1) the back door opener switch assembly, or 2) the certification ECU.
  2. If the back door entry unlock function using the back door control switch does not operate but the back door lock function operates, one of the following may be malfunctioning: 1) the back door control switch, or 2) the multiplex network door ECU (back door P/W); or the multiplex network door ECU (back door P/W) receives the back door control switch unlock signal, but is unable to send the signal to the certification ECU through LIN and CAN communication.

WIRING DIAGRAM


B241774E01


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  5. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.

    Result 
    Result
    Proceed to
    OK (back door opener switch operation fails)
    A
    OK (back door control switch operation fails)
    B
    NG
    C



B
Go to step 5

C
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
A


2.READ VALUE USING TECHSTREAM (UNLOCK SWITCH)
  1. Using the Techstream, read the Data List (Click here).

    Smart Key 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tr/B Door Unlock SW
    Back door unlock switch / ON or OFF
    ON: Back door unlock switch pushed
    OFF: Back door unlock switch not pushed
    -

    OK:
    "ON" (unlock switch is pushed) and "OFF" (unlock switch is not pushed) appear on the screen.



NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (Click here)  

3.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (UNLOCK SWITCH)
B241775E01
  1. Remove the back door opener switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UL) - 2 (E)
    No switch pushed
    10 kΩ or higher
    1 (UL) - 2 (E)
    Unlock switch pushed
    Below 1 Ω



NG
REPLACE BACK DOOR OPENER SWITCH ASSEMBLY (UNLOCK SWITCH) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH - CERTIFICATION ECU)
  1. Disconnect the back door opener switch connector.

  1. Disconnect the F79 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (UL) - F79-22 (TSW5)
    Always
    Below 1 Ω
    2 (E) - Body ground
    Always
    Below 1 Ω
    1 (UL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (Click here)  

5.READ VALUE USING TECHSTREAM (UNLOCK SWITCH)
  1. Using the Techstream, read the Data List (Click here).

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Outside Back Door P/W Down SW
    Unlock switch on back door control switch signal / ON or OFF
    ON: Unlock switch on back door control switch pushed
    OFF: Unlock switch on back door control switch not pushed
    -

    OK:
    "ON" (unlock switch is pushed) and "OFF" (unlock switch is not pushed) appear on the screen.



NG
Go to step 6
OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) (Click here)  

6.INSPECT BACK DOOR CONTROL SWITCH (UNLOCK SWITCH)
B241776E01
  1. Remove the back door control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (SDN) - 2 (E3)
    No switch pushed
    10 kΩ or higher
    3 (SDN) - 2 (E3)
    Unlock switch pushed
    Below 1 Ω



NG
REPLACE BACK DOOR CONTROL SWITCH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (BACK DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU)
  1. Disconnect the W11 switch connector.

  1. Disconnect the W10 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W11-3 (SDN) - W10-9 (SDN)
    Always
    Below 1 Ω
    W11-2 (E3) - W10-21 (E3)
    Always
    Below 1 Ω
    W11-3 (SDN) - Body ground
    Always
    10 kΩ or higher
    W11-2 (E3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W) (Click here)