Home › Drivetrain · A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2772    Four Wheel Drive (4WD) Low Switch Circuit Range / Performance

for Preparation Click here


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.
This DTC indicates that the transfer L4 position switch remains on.

DTC Code
DTC Detection Condition
Trouble Area
P2772
Transfer L4 position switch remains on while the vehicle is being driven under the following conditions for 1.8 sec. or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer in H4.
  1. Short in transfer L4 position switch circuit
  2. Transfer system
  3. ECM

MONITOR DESCRIPTION

Full Time 4WD
  1. The ECM monitors the transfer-case L4 position switch to determine when the transfer-case L4 gears are engaged. If the transfer-case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:
    1. The L4 switch indicates that the L4 transfer-case gears are engaged.
    2. The transfer-case shifter is in the "H4" position.
    3. The transfer-case output shaft speed is between 1000 and 3000 rpm.
    4. The specified time period has elapsed.
Part Time 4WD
  1. The ECM monitors the transfer L4 position switch to determine when the transfer-case L4 gear is engaged. If the transfer-case L4 gears remain engaged under all of the following conditions, the ECM will conclude that there is a malfunction of the transfer L4 position switch, illuminate the MIL and store the DTC:
    1. The transfer L4 position switch indicates that the L4 transfer-case gears are engaged.
    2. The transfer-case shift lever is in "H".
    3. The transfer-case output shaft speed is between 1000 and 3000 rpm.
    4. The specified time period has elapsed.

MONITOR STRATEGY


Related DTCs
P2772: Transfer L4 position switch/Functional check
Required sensors/Components
Transfer L4 position switch
Frequency of operation
Continuous
Duration
ON malfunction (A): 1.8 sec.
ON malfunction (B): 0.5 sec.
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not stored
P0500 (Vehicle speed sensor circuit)
P0722 (Output speed sensor circuit)
Transfer neutral position switch
OFF

ON Malfunction (A) 
Output speed (Transfer output speed)
1000 to 3000 rpm

ON Malfunction (B) 
Output speed (Transfer output speed)
143 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met: ON malfunction (A) and (B)

ON Malfunction (A) 
L4 switch
ON

ON Malfunction (B) 
Actual transfer gear ratio
Transfer input speed/Transfer output speed
0.9 or more, and less than 1.1

WIRING DIAGRAM


C214970E03


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)


    C209926E08
  1. Disconnect the F47 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F47-21 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Four Wheel Drive Control ECU)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for VF4BM Transfer)
    B
    OK (for VF2A Transfer)
    C
    OK (for VF2BM Transfer)
    D



B
GO TO TRANSFER SYSTEM (Click here)

C
GO TO TRANSFER SYSTEM (Click here)

D
GO TO TRANSFER SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)


    C214333E02
  1. Disconnect the F51 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F51-16 (L4) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)