Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1642/81    Lost Communication with Side Satellite Sensor Bus RH

DTC    B1647/82    Lost Communication with Side Satellite Sensor Bus LH

for Preparation Click here


DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, rear airbag sensor LH or RH and side airbag sensor LH or RH.
The side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1642/81 or B1647/82 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH).

DTC Code
DTC Detection Condition
Trouble Area
B1642/81
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) for 2 seconds.
  2. A side airbag sensor RH malfunction.
  3. A rear airbag sensor RH malfunction.
  4. A center airbag sensor malfunction.
  1. Floor wire
  2. Front door wire RH
  3. Side airbag sensor assembly RH
  4. Rear airbag sensor RH
  5. Center airbag sensor assembly
B1647/82
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag LH and curtain shield airbag LH) for 2 seconds.
  2. A side airbag sensor LH malfunction.
  3. A rear airbag sensor LH malfunction.
  4. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front door wire LH
  3. Side airbag sensor assembly LH
  4. Rear airbag sensor LH
  5. Center airbag sensor assembly

WIRING DIAGRAM


C175145E04


C175145E03


INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1642 and B1647 are not output
    A
    DTC B1647 is output
    B
    DTC B1642 is output
    C

    HINT:
    Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
Go to step 11
C


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and rear airbag sensor RH.



    C208245E01
  1. Check that the connectors (on the center airbag sensor side and rear airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Center Airbag Sensor



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR RH)


  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


    C213919E01


    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Center Airbag Sensor
    *3
    Floor Wire
    *4
    Connector C
    *5
    Connector B
    *6
    Service Wire
    *a
    Rear view of wire harness connector
    (to Rear Airbag Sensor RH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N9-4 (BBR+) - Body ground
    Ignition switch ON
    Below 1 V
    N9-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-4 (BBR+) - N9-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-4 (BBR+) - N9-3 (BBR-)
    Always
    1 MΩ or higher
    N9-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    N9-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


5.CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the side airbag sensor RH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTOR PROPERLY
OK


6.CHECK CONNECTORS
  1. Disconnect the connector from the side airbag sensor RH.



    C213962E01
  1. Check that the connector (on the side airbag sensor RH side) is not damaged.

    OK:
    The connector is not deformed or damaged.

    Text in Illustration 
    *1
    Side Airbag Sensor RH
    *2
    Rear Airbag Sensor RH



NG
REPLACE HARNESS AND CONNECTOR
OK


7.CHECK SIDE AIRBAG SENSOR RH CIRCUIT


  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


    C213922E01


    Text in Illustration 
    *1
    Side Airbag Sensor RH
    *2
    Rear Airbag Sensor RH
    *3
    Connector E
    *4
    Connector B
    *5
    Service Wire
    -
    -
    *a
    Rear view of wire harness connector
    (to Side Airbag Sensor RH)
    *b
    Rear view of wire harness connector
    (to Rear Airbag Sensor RH)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N9-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    N9-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-1 (BCR+) - N9-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-1 (BCR+) - N9-2 (BCR-)
    Always
    1 MΩ or higher
    N9-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N9-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 10
OK


8.CHECK REAR AIRBAG SENSOR RH


    C171812E03
  1. Connect the connector to the center airbag sensor and side airbag sensor RH.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1642 and B1647 are not output
    A
    DTC B1647 is output
    B
    DTC B1642 is output
    C

    HINT:
    Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Center Airbag Sensor

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE REAR AIRBAG SENSOR RH (Click here)
C


9.CHECK SIDE AIRBAG SENSOR RH


    C171828E15
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1642 and B1647 are not output
    A
    DTC B1647 is output
    B
    DTC B1642 is output
    C

    HINT:
    Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Side Airbag Sensor LH
    *2
    Rear Airbag Sensor RH

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

10.CHECK FLOOR WIRE (REAR AIRBAG SENSOR RH - FRONT DOOR WIRE RH)


  1. Disconnect the floor wire connector from the front door wire RH.


    C213921E01


    Text in Illustration 
    *1
    Side Airbag Sensor RH
    *2
    Rear Airbag Sensor RH
    *3
    Front Door Wire RH
    *4
    Floor Wire
    *5
    Connector C
    *6
    Connector B
    *7
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Front Door Wire RH)
    *b
    Rear view of wire harness connector
    (to Rear Airbag Sensor RH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N9-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    N9-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-1 (BCR+) - N9-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-1 (BCR+) - N9-2 (BCR-)
    Always
    1 MΩ or higher
    N9-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N9-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT DOOR WIRE RH 

11.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


12.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and rear airbag sensor LH.



    C208244E01
  1. Check that the connectors (on the center airbag sensor side and rear airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Center Airbag Sensor



NG
REPLACE NO. 2 FLOOR WIRE
OK


13.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR LH)


  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


    C213920E01


    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Center Airbag Sensor
    *3
    No. 2 Floor Wire
    *4
    Connector C
    *5
    Connector B
    *6
    Service Wire
    *a
    Rear view of wire harness connector
    (to Rear Airbag Sensor LH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O8-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    O8-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-4 (BBL+) - O8-3 (BBL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-4 (BBL+) - O8-3 (BBL-)
    Always
    1 MΩ or higher
    O8-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    O8-3 (BBL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


14.CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the side airbag sensor LH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTOR PROPERLY
OK


15.CHECK CONNECTORS
  1. Disconnect the connector from the side airbag sensor LH.



    C213962E01
  1. Check that the connector (on the side airbag sensor LH side) is not damaged.

    OK:
    The connector is not deformed or damaged.

    Text in Illustration 
    *1
    Side Airbag Sensor LH
    *2
    Rear Airbag Sensor LH



NG
REPLACE HARNESS AND CONNECTOR
OK


16.CHECK SIDE AIRBAG SENSOR LH CIRCUIT


  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


    C213922E02


    Text in Illustration 
    *1
    Side Airbag Sensor LH
    *2
    Rear Airbag Sensor LH
    *3
    Connector E
    *4
    Connector B
    *5
    Service Wire
    -
    -
    *a
    Rear view of wire harness connector
    (to Side Airbag Sensor LH)
    *b
    Rear view of wire harness connector
    (to Rear Airbag Sensor LH)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O8-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    O8-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-1 (BCL+) - O8-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-1 (BCL+) - O8-2 (BCL-)
    Always
    1 MΩ or higher
    O8-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O8-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 19
OK


17.CHECK REAR AIRBAG SENSOR LH


    C146229E37
  1. Connect the connector to the center airbag sensor and side airbag sensor LH.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1642 and B1647 are not output
    A
    DTC B1642 is output
    B
    DTC B1647 is output
    C

    HINT:
    Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Center Airbag Sensor

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE REAR AIRBAG SENSOR LH (Click here)
C


18.CHECK SIDE AIRBAG SENSOR LH


    C171828E15
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 90 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1642 and B1647 are not output
    A
    DTC B1642 is output
    B
    DTC B1647 is output
    C

    HINT:
    Codes other than DTC B1642 and B1647 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Side Airbag Sensor RH
    *2
    Rear Airbag Sensor LH

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

19.CHECK NO. 2 FLOOR WIRE (REAR AIRBAG SENSOR LH - FRONT DOOR WIRE LH)


  1. Disconnect the No. 2 floor wire connector from the front door wire LH.


    C213921E03


    Text in Illustration 
    *1
    Side Airbag Sensor LH
    *2
    Rear Airbag Sensor LH
    *3
    Front Door Wire LH
    *4
    No. 2 Floor Wire
    *5
    Connector C
    *6
    Connector B
    *7
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Front Door Wire LH)
    *b
    Rear view of wire harness connector
    (to Rear Airbag Sensor LH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O8-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    O8-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-1 (BCL+) - O8-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O8-1 (BCL+) - O8-2 (BCL-)
    Always
    1 MΩ or higher
    O8-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O8-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT DOOR WIRE LH