SFI SYSTEM > Fuel Pump Control Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether operating sounds can be heard while operating the fuel pump using the Techstream.
|
| ||||
| OK | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP) |
![]() |
Remove the fuel tank assembly (Click here).
Remove the fuel pump from the fuel tank assembly.
Clean the fuel pump to completely remove any remaining fuel.
Connect the fuel pump connector.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.
Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | Techstream Operation | Specified Condition |
| 1 - 2 | FPC Duty: 25% | 3.2 to 4.05 V |
| FPC Duty: 80% | 8.8 to 12.5 V |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | Techstream Operation | Specified Condition |
| 1 - 2 | ON (FPC Duty: 90%) | 9.0 to 14.0 V |
| *a | Component with harness connected (Fuel Pump) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM) |
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q6-5 (FPC) - F51-3 (FPC) | Always | Below 1 Ω |
| Q6-5 (FPC) or F51-3 (FPC) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.REPLACE FUEL PUMP |
Replace the fuel pump (Click here).
|
| ||||
| 5.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 7.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the fuel pump ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Q6-6 (+B) - Body Ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Pump ECU) |
Reconnect the fuel pump ECU connector.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - BODY GROUND) |
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q6-3 (E) - Body ground | Always | Below 1 Ω |
Reconnect the fuel pump ECU connector.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU) |
Disconnect the fuel pump connector.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q5-4 (B2) - Q6-1 (FP) | Always | Below 1 Ω |
| Q5-5 (E2) - Q6-2 (FP-) | Always | Below 1 Ω |
| Q5-4 (B2) or Q6-1 (FP) - Body ground | Always | 10 kΩ or higher |
| Q5-5 (E2) or Q6-2 (FP-) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pump connector.
Reconnect the fuel pump ECU connector.
|
| ||||
| OK | |
| 10.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM) |
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q6-5 (FPC) - F51-3 (FPC) | Always | Below 1 Ω |
| Q6-5 (FPC) or F51-3 (FPC) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pump ECU connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 12.REPLACE FUEL PUMP ECU |
Replace the fuel pump ECU (Click here).
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check the fuel pump operation.
|
| ||||
| OK | ||
| ||
| 14.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN) |
Inspect the No. 1 integration relay (EFI MAIN) (Click here).
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (EFI MAIN RELAY - FUEL PUMP ECU) |
Remove the No. 1 integration relay from the engine room relay block.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2F-12 - Q6-6 (+B) | Always | Below 1 Ω |
| 2F-12 or Q6-6 (+B) - Body ground | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay.
Reconnect the fuel pump ECU connector.
|
| ||||
| OK | ||
| ||