Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

DTC    B27A1    Open in Driver Side Electrical Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the front door outside handle assembly (for driver side) at an interval of 250 ms. The front door outside handle assembly (for driver side) detects when the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the driver door, the signal is transmitted at an interval of 250 ms. DTC B27A1 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for driver side) (CLG1 - ANT1, CG1B - ANT2).

DTC Code
DTC Detection Condition
Trouble Area
B27A1
An open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for driver side) (CLG1 - ANT1, CG1B - ANT2).
  1. Harness or connector
  2. Front door outside handle assembly (for driver side)
  3. Certification ECU

WIRING DIAGRAM


B242658E01


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and front door outside handle assembly (for driver side).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the M1 handle connector.

  1. Disconnect the F79 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-3 (ANT2) - F79-4 (CG1B)
    Always
    Below 1 Ω
    M1-6 (ANT1) - F79-3 (CLG1)
    Always
    Below 1 Ω
    M1-2 (GND) - Body ground
    Always
    Below 1 Ω
    F79-4 (CG1B) - Body ground
    Always
    10 kΩ or higher
    F79-3 (CLG1) - Body ground
    Always
    10 kΩ or higher
    F79-15 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CERTIFICATION ECU


  1. Measure the voltage according to the value(s) in the table below.


    B224125E06


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU)
    -
    -

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    F79-3 (CLG1) - F79-15 (E)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    F79-4 (CG1B) - F79-15 (E)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation



NG
REPLACE CERTIFICATION ECU (Click here)
OK


4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE)
  1. Temporarily replace the front door outside handle assembly (for driver side) with a new or normally functioning one (Click here).


NEXT


5.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A1 is not output.



NG
REPLACE CERTIFICATION ECU (Click here)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)