Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

DTC    B27A7    Open in Inside Luggage Compartment Electrical Key Oscillator Circuit

for Preparation Click here


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the indoor No. 2 electrical key antenna (inside luggage). The indoor No. 2 electrical key antenna (inside luggage) detects that the electrical key is inside the vehicle and transmits the request signal received from the certification ECU. DTC B27A7 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and indoor No. 2 electrical key antenna (inside luggage) (CLG7 - CLG6, CG7B - CLGB).

DTC Code
DTC Detection Condition
Trouble Area
B27A7
An open circuit is detected in the circuit between the certification ECU and indoor No. 2 electrical key antenna (inside luggage) (CLG7 - CLG6, CG7B - CLGB).
  1. Harness or connector
  2. Indoor No. 2 electrical key antenna (inside luggage)
  3. Certification ECU

WIRING DIAGRAM


B210705E11


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and indoor No. 2 electrical key antenna (inside luggage).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (INDOOR NO. 2 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
  1. Disconnect the O14 antenna connector.

  1. Disconnect the F79 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O14-1 (CLG6) - F79-26 (CLG7)
    Always
    Below 1 Ω
    O14-3 (CLGB) - F79-27 (CG7B)
    Always
    Below 1 Ω
    F79-26 (CLG7) - Body ground
    Always
    10 kΩ or higher
    F79-27 (CG7B) - Body ground
    Always
    10 kΩ or higher
    F79-15 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK CERTIFICATION ECU


  1. Measure the voltage according to the value(s) in the table below.


    B224125E10


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU)
    -
    -

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    F79-26 (CLG7) - F79-15 (E)
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    F79-27 (CG7B) - F79-15 (E)
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation



NG
REPLACE CERTIFICATION ECU (Click here)
OK


4.REPLACE INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
  1. Temporarily replace the indoor No. 2 electrical key antenna (inside luggage) with a new or normally functioning one (Click here).


NEXT


5.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A7 is not output.



NG
REPLACE CERTIFICATION ECU (Click here)
OK

END (INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)