Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control switch condition. The battery supplies positive (+) battery voltage to the cruise control switch. Terminal 11 (CCS) of the ECM receives the voltage which varies according to the switch condition.

WIRING DIAGRAM


E200577E18


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (CRUISE CONTROL SWITCH)
  1. Use the Data List to check if the cruise control switch is functioning properly (Click here).

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Cruise control switch (Main CPU) / ON or OFF
    ON: Cruise control switch on
    OFF: Cruise control switch off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -SET switch signal / ON or OFF
    ON: -SET switch on
    OFF: -SET switch off
    -
    RES/ACC Switch
    +RES switch signal / ON or OFF
    ON: +RES switch on
    OFF: +RES switch off
    -

    OK:
    On screen, each item changes between ON and OFF according to above chart.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    E176804E05
  1. Replace the spiral cable sub-assembly (Click here).

  1. If there are any defects as follows, replace the spiral cable sub-assembly with a new one: scratches, cracks, dents or chips on the connector or spiral cable sub-assembly.

  1. Check the spiral cable sub-assembly.

    1. Set the spiral cable sub-assembly to the center position .

    2. Rotate the spiral cable sub-assembly 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

      NOTICE:
      As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (CCS) - 1 (CCS)
      Always
      Below 1 Ω
      4 (ECC) - 2 (ECC)

    3. Set the spiral cable sub-assembly to the center position and rotate the spiral cable sub-assembly 2.5 times clockwise. Then, while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (CCS) - 1 (CCS)
      Always
      Below 1 Ω
      4 (ECC) - 2 (ECC)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT CRUISE CONTROL SWITCH WIRE


    E178683E10
  1. Disconnect the z9 spiral cable connector.

  1. Disconnect the z10 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-3 (CCS) - z10-3 (CCS)
    Always
    Below 1 Ω
    z9-4 (ECC) - z10-1 (ECC)
    z9-3 (CCS) - Body ground
    Always
    10 kΩ or higher
    z9-4 (ECC) - Body ground



NG
REPLACE CRUISE CONTROL SWITCH WIRE
OK


4.INSPECT CRUISE CONTROL SWITCH


  1. Remove the cruise control switch (Click here).


    B215369E07

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (CCS) - 1 (ECC)
    Cruise control switch on
    Below 2.5 Ω
    Cruise control switch off
    1 MΩ or higher
    +RES switch held on
    235 to 245 Ω
    -SET switch held on
    617 to 643 Ω
    CANCEL switch held on
    1509 to 1571 Ω



NG
REPLACE CRUISE CONTROL SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
  1. Disconnect the F23 spiral cable connector.

  1. Disconnect the F50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F23-1 (CCS) - F50-11 (CCS)
    Always
    Below 1 Ω
    F23-2 (ECC) - Body ground
    F23-1 (CCS) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)