Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15CC    Backup Battery Failure

for Preparation Click here


DESCRIPTION

This DTC is stored when the DCM (Telematics Transceiver) detects one of the following:
  1. Open or short in the BUB (Back-Up Battery) circuit.
  2. The BUB (Back-Up Battery) voltage drops or the BUB (Back-Up Battery) malfunctions.
  3. The BUB (Back-Up Battery) temperature is temporarily high.

DTC Code
DTC Detection Condition
Trouble Area
B15CC
Back-up battery malfunction.
  1. Harness or connector
  2. BUB (Back-Up Battery)
  3. DCM (Telematics Transceiver)

WIRING DIAGRAM


E196669E09


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and wait for 10 seconds.

  1. Perform "Health Check" and check for current DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B15CC is output
    A
    DTC B15CC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK HARNESS AND CONNECTOR (DCM - BUB)


    E196671E10
  1. Disconnect the F39 DCM (Telematics Transceiver) connector.

  1. Disconnect the F40 BUB (Back-Up Battery) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-30 (BBI+) - F40-1 (BBO+)
    Always
    Below 1 Ω
    F39-13 (BBI-) - F40-5 (BBO-)
    Always
    Below 1 Ω
    F39-20 (CTR1) - F40-3 (BTR1)
    Always
    Below 1 Ω
    F39-21 (CTR2) - F40-4 (BTR2)
    Always
    Below 1 Ω
    F39-30 (BBI+) - Body ground
    Always
    10 kΩ or higher
    F39-13 (BBI-) - Body ground
    Always
    10 kΩ or higher
    F39-20 (CTR1) - Body ground
    Always
    10 kΩ or higher
    F39-21 (CTR2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DCM [Telematics Transceiver])
    *b
    Front view of wire harness connector
    (to BUB [Back-Up Battery])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE BUB (BACK-UP BATTERY)
  1. Replace the BUB (Back-Up Battery) with a normal one and check that the same problem does not occur again (Click here).

    NOTICE:
    The BUB (Back-Up Battery) must not be replaced while an ACN call is in progress (Click here).


NEXT


4.CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


5.CHECK FOR DTC
  1. Check for DTCs and check that the same trouble does not occur again (Click here).

    OK:
    DTC B15CC is not output.



NG
Go to step 6
OK

END 

6.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)