Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B1572    Telephone Microphone Error

for Preparation Click here


DESCRIPTION

This DTC is stored when the DCM (Telematics Transceiver) detects a malfunction in the telephone microphone assembly circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1572
Current of MCVD reaches the malfunction criteria for 10 seconds when the ignition switch is ON.
  1. Harness or connector
  2. Telephone microphone assembly
  3. Map light assembly
  4. DCM (Telematics Transceiver)

WIRING DIAGRAM


E192507E21


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and wait for 10 seconds.

  1. Perform "Health Check" and check for current DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1572 is output
    A
    DTC B1572 is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.CHECK MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE POWER SOURCE)


    E195983E07
  1. Remove the map light assembly with the connector connected (Click here).

  1. Measure the voltage according to the value(s) in the table below

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    U2-14 (MACC) - Body ground
    Ignition switch ON
    4 to 6 V

    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (DCM - MAP LIGHT ASSEMBLY)


    E199654E01
  1. Disconnect the F39 DCM (Telematics Transceiver) connector.

  1. Disconnect the U2 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F39-34 (MCI+) - U2-13 (MCO+)
    Always
    Below 1 Ω
    F39-35 (MCI-) - U2-12 (MCO-)
    Always
    Below 1 Ω
    F39-34 (MCI+) - Body ground
    Always
    10 kΩ or higher
    F39-35 (MCI-) - Body ground
    Always
    10 kΩ or higher
    F39-32 (SGND) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to DCM [Telematics Transceiver])
    *b
    Front view of wire harness connector
    (to Map Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a normal one and check that the same problem does not occur again (Click here).

    OK:
    The system returns to normal.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END 

5.CHECK DCM (TELEMATICS TRANSCEIVER) (TELEPHONE MICROPHONE POWER SOURCE)


    E197427E07
  1. Remove the DCM (Telematics Transceiver) with the connectors connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F39-33 (MCVD) - Body ground
    Ignition switch ON
    4 to 6 V

    Text in Illustration 
    *a
    Component with harness connected
    (DCM [Telematics Transceiver])



NG
Go to step 6
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

6.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)