DTC P1160 Throttle Valve Return Spring Malfunction |
DTC P2119 Throttle Actuator Control Throttle Body Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1160 | After setting throttle valve opening angle at 40% in throttle actuator control, the change in opening angle is less than 2°after throttle actuator has been off. (1 trip detection logic) | Throttle with motor body assembly |
| P2119 | The throttle valve opening angle continues to vary greatly from the target opening angle. (1 trip detection logic) |
|
| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1160 OR P2119) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P1160 and/or P2119 is output | A |
| DTC P1160 and/or P2119 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING GTS (THROTTLE POSITION) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine / Data List / Throttle Position No. 1 and Throttle Position Command.
Read the values displayed on the GTS while fully depressing and releasing the accelerator pedal quickly.
| Result | Proceed to |
| Throttle Position No. 1 does not change | A |
| Throttle Position No. 1 changes even a little | B |
|
| ||||
| A | |
| 3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
Inspect the throttle with motor body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for contamination between the throttle valve and housing. If necessary, clean the throttle with motor body assembly. Also, check that the throttle valve moves smoothly.
|
| ||||
| OK | |
| 5.READ VALUE USING GTS (THROTTLE POSITION) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
Read the values displayed on the GTS while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| Value in Data List changes when wire harness is wiggled, or DTC is output | A |
| Other than above | B |
|
| ||||
| A | |
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY) |
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector.
| NEXT | ||
| ||
| 7.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P1160 and/or P2119 is output | B |
|
| ||||
| A | ||
| ||