Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use these procedures to troubleshoot the engine immobiliser system.
  1. *: Use the GTS.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.INSPECT BATTERY VOLTAGE

      Standard voltage:
      11 to 14 V

      1. If the voltage is below 11 V, recharge or replace the battery before proceeding.

      HINT:
      A simple method to determine whether the battery is depleted is to operate the horn.


    NEXT


    3.TURN ENGINE SWITCH ON (IG)

      HINT:
      If the engine switch cannot be turned on (IG), communication with the GTS can be confirmed by connecting the GTS to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins.


    NEXT


    4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
    1. Use the GTS to check if the CAN communication system is functioning normally (Click here).
      Result 
      Result
      Proceed to
      CAN DTC is not output
      A
      CAN DTC is output
      B



    B.
    GO TO CAN COMMUNICATION SYSTEM (Click here)
    A


    5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
    1. Use the GTS to check if the LIN communication system is functioning normally (Click here).
      Result 
      Result
      Proceed to
      LIN DTC is not output
      A
      LIN DTC is output
      B



    B.
    GO TO LIN COMMUNICATION SYSTEM (Click here)
    A


    6.CHECK FOR DTC (ENTRY AND START SYSTEM)*
    1. Check for DTCs and make a note of any codes that are output.

    2. Clear the DTCs (Click here).

    3. Recheck for DTCs. Based on the DTCs output above, try to duplicate the engine immobiliser system DTC or steering lock system DTC by simulating the symptoms indicated by the DTCs.
      Result 
      Result
      Proceed to
      DTC is not output
      A
      Steering lock system DTC is output (DTC B2781, B2782 or B2788)
      B
      Engine immobiliser system DTC is output (except DTC B2781, B2782 and B2788)
      C



    B.
    GO TO STEERING LOCK SYSTEM (Click here)

    C.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
    A


    7.CHECK FOR DTC (SFI SYSTEM)*
    1. Clear the DTCs (Click here).

    2. Check for DTCs (Click here).

    3. HINT:
      The DTCs for the engine immobiliser system are specified above. If other codes are output, check the DTC chart for the SFI system.

      Result 
      Result
      Proceed to
      DTC is not output
      A
      Engine immobiliser system DTC is output (DTC B2799, B279A or B279C)
      B
      SFI system DTC is output)
      C


    B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

    C.
    GO TO SFI SYSTEM (Click here)
    A


    8.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).
      Result 
      Result
      Proceed to
      Fault is not listed in problem symptoms table
      A
      Fault is listed in problem symptoms table
      B



    B.
    Go to step 10
    A


    9.OVERALL ANALYSIS AND TROUBLESHOOTING*
    1. Check Data List / Active Test (Click here).

    2. Check Terminals of ECU (Click here).


    NEXT


    10.ADJUST, REPAIR OR REPLACE

      NEXT


      11.CHECK FOR DTC*
      1. Clear the DTCs (Click here).

      2. Check for DTCs (Click here).

        HINT:
        Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure (Click here).

        Result 
        Result
        Proceed to
        DTC is not output
        A
        Engine immobiliser system DTC is output
        B



      B.
      GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
      A

      END