Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0441    Evaporative Emission Control System Incorrect Purge Flow

for Preparation Click here


DTC SUMMARY


DTC No.
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0441
Purge flow
While engine running, following conditions successively met:
  1. The pressure difference between non-purge and purge is less than threshold for 26 seconds or more.
  2. Regardless of forced vent valve on (close) and purge being carried out, the pressure difference between non-purge and purge is less than threshold for 21 seconds or more.
  1. Purge valve
  2. Purge line
  3. Connector/wire harness (Purge valve - ECM)
  4. ECM
  5. Leak from EVAP system
While engine running
2 trip

DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System (Click here).

MONITOR DESCRIPTION

The purge flow monitor runs while the engine is running. The purge flow monitor consists of 2 monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.

  1. The 1st monitor
    While the engine is running and the purge valve is on (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If the variation in the pressure is less than threshold, the ECM begins the 2nd monitor.


    A282471E02


  2. The 2nd monitor
    The vent valve is turned on (closed) and the EVAP pressure is then measured. If the variation in the pressure is more than threshold, the ECM interprets this as the purge valve being stuck closed, and illuminates the MIL and stores DTC P0441 (2 trip detection logic).


    A282472E01


CONFIRMATION DRIVING PATTERN


A285189E01

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Start the engine.
  7. Drive the vehicle at 60 km/h (40 mph) or more for 10 minute or more [A].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All readiness.
  11. Input the DTC: P0441.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  13. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
A280659E01
  1. Connect a GTS to the DLC3.

  1. Disconnect the vacuum hose (canister side) from the purge valve.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EVAP Control.

  1. When the purge valve is operated using the GTS, check whether the port of the purge valve applies suction to your finger.

OK:
Tester Operation
Tester Operation
VSV ON
Purge valve port applies suction to finger
VSV OFF
Purge valve port applies no suction to finger

Text in Illustration 
*a
Purge valve ON
*b
Purge valve OFF


NG
Go to step 3
OK


2.INSPECT EVAP LEAK PART
  1. Check for leakage from EVAP system (hose, disconnection, cracks, etc.).

OK:
No leakages in the EVAP purge line



NG
Go to step 4
OK


Go to step 5

3.REPLACE PURGE VALVE
  1. Replace the purge valve (Click here).



NEXT
Go to step 5

4.REPAIR OR REPLACE EVAP PURGE LINE

NEXT


5.CHECK DTC OUTPUT (EVAP SYSTEM)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.


Result 
Result
Proceed to
EVAP system DTCs are output
A
No DTCs output
(No pending DTCs output)
B


B
END
A


6.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


7.CHECK DTC OUTPUT (EVAP SYSTEM)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

HINT:
If no pending DTCs are found, the repair has been successfully completed.


NEXT

END