Home › Drivetrain ยท TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0756    Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

DTC    P0757    Shift Solenoid "B" Stuck ON (S2 Solenoid)

for Preparation Click here


SYSTEM DESCRIPTION

The TCM carries out detection of the gear position based upon signals from the input speed sensor NT and the output speed sensor SP2. Subsequently, if the gear position as detected by the TCM is different to the commanded gear position, then a related solenoid valve, valve body, or automatic transmission mechanical problem is detected.

DTC No.
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P0756
  1. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature 40°C (104°F) or more. (However, abnormalities with the shift solenoid valve S1, S2, S3, S4, SR, SL1, SL2, SLT), input speed sensor NT, output speed sensor SP2, park/neutral position switch, CAN bus, ECM communication, coolant temperature sensor, air flow sensor, electronically control throttle, and accelerator pedal sensor are not detected)
  2. The following conditions are met:
    1. When the TCM commands shifting to 1st, the actual gear position is shifted to 3rd.
    2. When the TCM commands shifting to 6th, the actual gear position is shifted to 5th.
  3. -
  4. 2-trip detection logic
  1. Shift solenoid valve S2
  2. Transmission wire
  3. Harness and connector
  4. TCM
P0757
  1. While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature 40°C (104°F) or more. (However, abnormalities with the shift solenoid valve S1, S2, S3, S4, SR, SL1, SL2, SLT), input speed sensor NT, output speed sensor SP2, park/neutral position switch, CAN bus, ECM communication, coolant temperature sensor, air flow sensor, electronically control throttle, and accelerator pedal sensor are not detected)
  2. The following conditions are met:
    1. When the TCM commands shifting to 5th, the actual gear position is shifted to 6th.
    2. When the TCM commands shifting to 6th, the actual gear position is shifted to 6th.
  3. -
  4. 2-trip detection logic
  1. Shift solenoid valve S2
  2. Transmission wire
  3. Harness and connector
  4. TCM

HINT:
  1. Gear positions in the event of a solenoid valve mechanical problem:

    TCM command gearshift
    1st
    2nd
    3rd
    4th
    5th
    6th
    *1: Actual gear position under S2 stuck ON malfunction
    ↑
    ↑
    2nd
    ↑
    6th
    ↑
    *2: Actual gear position under S2 stuck OFF malfunction
    3rd
    3rd
    3rd
    ↑
    5th
    5th


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S2.
The TCM commands gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.

WIRING DIAGRAM


C250709E02


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


CHECK THE SHIFT POSITION
  1. Drive the vehicle with shift lever in the M.

  2. Check the shift position.

    HINT:
    1. The shift solenoid valve S2 is turned on/off normally when the shift lever is in the D position:

      TCM command gearshift
      1st
      2nd
      3rd
      4th
      5th
      6th
      Shift solenoid valve S2
      ON
      ON
      OFF
      OFF
      OFF
      ON

1.CHECK OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and push the GTS main switch ON.

  1. Read the DTCs using the GTS (Click here).

    Result:

    Display (DTC output)
    Proceed to
    Only "P0756 and P2714" or "P0757" is output
    A
    "P0756 and P2714" or "P0757" and other DTCs
    B



B
GO TO DTC CHART (Click here)
A


2.HYDRAULIC TEST

C261940E01


Text in Illustration 
*1
SST
*2
Test Plug

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 60 to 90°C (140 to 194°F)
  2. The line pressure test should always be carried out in pairs. One technician should observe the conditions of wheels or wheel stoppers outside the vehicle while the other is performing the test.
  3. Be careful to prevent SST hose from interfering with the exhaust pipe.
  4. This Check must be conducted after checking and adjusting engine.
  5. Perform under condition that A/C is OFF.
  6. When conducting stall test, do not continue more than 5 seconds.

  1. Warm up the ATF (Automatic Transmission Fluid).

  1. Lift the vehicle up.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Lower the vehicle.

  1. Fully apply the parking brake and check the 4 wheels.

  1. Start the engine and check idling speed.

  1. Keep your left foot pressing firmly on the brake pedal and shift into D position.

  1. Measure the line pressure when the engine is idling.

  1. Depress the accelerator pedal all the way down. Quickly read the highest line pressure when engine speed reaches stall speed.

  1. In the same manner, do the test in R position.

    Specified line pressure: 
    Condition
    D position kPa (kgf / cm2, psi)
    R position kPa (kgf / cm2, psi)
    Idling
    350 to 430 kPa
    (3.6 to 4.4 kgf/cm2, 51 to 62 psi)
    760 to 950 kPa
    (7.7 to 9.7 kgf/cm2, 110 to 138 psi)
    Stall test
    1200 to 1380 kPa
    (12.5 to 14.0 kgf/cm2, 174 to 200 psi)
    1410 to 1630 kPa
    (14.4 to 16.6 kgf/cm2, 204 to 236 psi)



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


3.INSPECT SHIFT SOLENOID VALVE S2
  1. Remove the shift solenoid valve S2.

  1. Perform inspection of the shift solenoid valve S2 .



NG
REPLACE SHIFT SOLENOID VALVE S2 (Click here)
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Perform inspection of the transmission valve body assembly (Click here).

OK:
There are no foreign objects on each valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)