Home › Drivetrain · TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2762    Torque Converter Pressure Control Solenoid Circuit Performance (SLU / DSU Solenoid)

DTC    P2763    Torque Converter Clutch Pressure Control Solenoid Control Circuit High (Shift Solenoid Valve DSU)

DTC    P2764    Torque Converter Clutch Pressure Control Solenoid Control Circuit Low (Shift Solenoid Valve DSU)

for Preparation Click here


DESCRIPTION

The shift solenoid valve SLU is controlled by the duty ratio as determined in advance by the TCM. In this way, it carries out lock-up and flex lock-up control.

DTC No.
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P2762
  1. Not learning control prohibited status.
    Not open or short in the shift solenoid valve SLU/DSU circuit.
  2. The difference between the shift solenoid valve SLU operational specified current and operational feedback current is 12 A or more in total.
  3. Detects "2.Malfunction Status" 5 times consecutively.
  4. 1-trip detection logic
  1. Shift solenoid valve SLU
  2. Transmission wire
  3. Harness and connector
  4. TCM
P2763
  1. Not learning control prohibited status
    Not malfunction with the shift solenoid valve SLU/DSU circuit performance.
  2. 1 second or more has elapsed after turning shift solenoid valve SLU off.
    The shift solenoid valve SLU operational feedback voltage is 0.018 V or less.
  3. Detects malfunction that continues for 100 ms or more 5 times consecutively.
  4. 1-trip detection logic
  1. Shift solenoid valve SLU
  2. Transmission wire
  3. Harness and connector
  4. TCM
P2764
  1. Not learning control prohibited status
    Not malfunction with the shift solenoid valve SLU/DSU circuit performance.
  2. 1 second or more has elapsed after turning shift solenoid valve SLU on.
    The shift solenoid valve SLU operational feedback voltage is 0.257 V or more.
  3. Detects malfunction that continues for 100 ms or more 5 times consecutively.
  4. 1-trip detection logic
  1. Shift solenoid valve SLU
  2. Transmission wire
  3. Harness and connector
  4. TCM

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit or feedback Stuck is detected, the TCM determines there is a malfunction. The TCM will turn on the MIL and store this DTC.

WIRING DIAGRAM


C250701E05


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.INSPECT TRANSMISSION WIRE (SLU)
  1. Disconnect the L4 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-12(SLU+) - L4-5(SLU-)
    20°C(68°F)
    5.0 to 5.6 Ω
    L4-12(SLU+) - Body ground
    Always
    10 kΩ or higher
    L4-5(SLU-) - Body ground
    Always
    10 kΩ or higher

  1. Connect the L4 transmission wire connector.



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
  1. Disconnect the A18 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A18-13(SLU+) - A18-1(SLU-)
    20°C(68°F)
    5.0 to 5.6 Ω
    A18-13(SLU+) - Body ground
    Always
    10 kΩ or higher
    A18-1(SLU-) - Body ground
    Always
    10 kΩ or higher

  1. Connect the A18 TCM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE TCM
  1. Replace the TCM (Click here).


NEXT

PERFORM THE RESET MEMORY (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SLU
  1. Remove the shift solenoid valve SLU (Click here).

  1. Perform inspection of the shift solenoid valve SLU .



NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)