Home › Drivetrain · TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0961    Pressure Control Solenoid "A" Performance (SL1 Solenoid)

DTC    P0962    Pressure Control Solenoid "A" Circuit Low (SL1 Solenoid)

DTC    P0963    Pressure Control Solenoid "A" Circuit High (SL1 Solenoid)

for Preparation Click here


DESCRIPTION

Based upon a signal from the TCM, the combination of shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2) changes the gear position from 1st to 6th. As a fail-safe function if the solenoid valve system is open or shorted, the TCM cuts power to all solenoids, leaving just the mechanical hydraulic circuit, requiring manual shifting.

DTC No.
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P0961
  1. Not learning control prohibited status
    Not open or short in the shift solenoid valve SL1 circuit
  2. The difference between the shift solenoid valve SL1 operational feedback current is 12 A or more in total.
  3. Detects "2.Malfunction Status" 2 times consecutively.
  4. 1-trip detection logic
  1. Shift solenoid valve SL1
  2. Transmission wire
  3. Harness and connector
  4. TCM
P0962
  1. Not learning control prohibited status
    1 second or more has elapsed after turning shift solenoid valve SL1 off.
  2. The shift solenoid valve SL1 operational feedback voltage is 0.018 V or less.
  3. Detects malfunction that continues for 100 ms or more 5 times consecutively.
  4. 1-trip detection logic
  1. Shift solenoid valve SL1
  2. Transmission wire
  3. Harness and connector
  4. TCM
P0963
  1. Not learning control prohibited status
    1 second or more has elapsed after turning shift solenoid valve SL1 on.
  2. The shift solenoid valve SL1 operational feedback voltage is 0.257 V or more.
  3. Detects malfunction that continues for 100 ms or more 5 times consecutively.
  4. 1-trip detection logic
  1. Shift solenoid valve SL1
  2. Transmission wire
  3. Harness and connector
  4. TCM
Reference (Using an oscilloscope):
Check the waveform between the terminals SL1+ and SL1- of the TCM connector
G023426E05

Standard:
Refer to the illustration.

Terminal
SL1+ - SL1-
Tool setting
5 V/DIV., 1 ms./DIV.
Vehicle condition
5th or 6th gear

MONITOR DESCRIPTION

This DTC indicates an open, short, or feedback stuck in the shift solenoid valve SL1 circuit. The TCM commands gearshift by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC.

WIRING DIAGRAM


C250701E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
  1. The shift solenoid valve SL1 is turned on/off normally when the shift lever is in the D position:

    TCM command gearshift
    1st
    2nd
    3rd
    4th
    5th
    6th
    Shift solenoid valve SL1
    OFF
    OFF
    OFF
    OFF
    ON
    ON

1.INSPECT TRANSMISSION WIRE (SL1)
  1. Disconnect the L4 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-13(SL1+) - L4-6(SL1-)
    20°C(68°F)
    5.0 to 5.6 Ω
    L4-13(SL1+) - Body ground
    Always
    10 kΩ or higher
    L4-6(SL1-) - Body ground
    Always
    10 kΩ or higher

  1. Connect the L4 transmission wire connector.



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
  1. Disconnect the A18 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A18-16(SL1+) - A18-12(SL1-)
    20°C(68°F)
    5.0 to 5.6 Ω
    A18-16(SL1+) - Body ground
    Always
    10 kΩ or higher
    A18-12(SL1-) - Body ground
    Always
    10 kΩ or higher

  1. Connect the A18 TCM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE TCM
  1. Replace the TCM (Click here).


NEXT

PERFORM THE RESET MEMORY (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SL1
  1. Remove the shift solenoid valve SL1 (Click here).

  1. Perform inspection of the shift solenoid valve SL1 .



NG
REPLACE SHIFT SOLENOID VALVE SL1 (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)