DTC P0030 A/F Sensor Heater Control Circuit (Bank 1 Sensor 1) |
DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0030 | Air fuel ratio sensor impedance is greater than 65 Ω for 10 seconds or more. (2 trip detection logic) |
|
| P0031 | Air fuel ratio sensor heater voltage is less than 1.2 V for 1 second or more. (1 trip detection logic) | |
| P0032 | Air fuel ratio sensor heater voltage is 1.2 V or more for 2 seconds or more. (1 trip detection logic) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 2.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C14-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A34-5 (HA1A) - C14-1(HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A34-5 (HA1A) or C14-1 (HA1A) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (P0030, P0031 OR P0032) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0030, P0031or P0032 is output | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT RELAY (EFI MAIN2) |
Check the EFI MAIN2 relay .
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - EFI MAIN2 RELAY) |
Disconnect the air fuel ratio sensor connector.
Remove the EFI MAIN2 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI MAIN2 relay terminal 3 - C14-2 (+B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| EFI MAIN2 relay terminal 3 or C14-2 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||