Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0851    Park / Neutral Switch Input Circuit Low

DTC    P0852    Park / Neutral Switch Input Circuit High

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P0851
for Manual Transmission
  1. No non-neutral position detected in shift change running state (judged based on changes in the relationship between vehicle speed and engine speed) (2 trip detection logic)
for Automatic Transmission
  1. The CAN data received from the TCM is "P or N" position signal while the park/neutral position switch assembly is not in P or N position. (2 trip detection logic)
for Manual Transmission
  1. Open or short in neutral position switch signal circuit
  2. Neutral position switch
  3. ECM
for Automatic Transmission
  1. Open or short in park/neutral position switch signal circuit
  2. Park/neutral position switch assembly
  3. ECM
  4. TCM
P0852
for Manual Transmission
  1. No neutral position detected in shift change running state (judged based on changes in the relationship between vehicle speed and engine speed) (2 trip detection logic)
for Automatic Transmission
  1. The CAN data received from the TCM is other than "P or N" position signal while the park/neutral position switch assembly is in P or N position. (2 trip detection logic)
for Manual Transmission
  1. Open or short in neutral position switch signal circuit
  2. Neutral position switch
  3. ECM
for Automatic Transmission
  1. Open or short in park / neutral position switch signal circuit
  2. Park/neutral position switch assembly
  3. ECM
  4. TCM

MONITOR DESCRIPTION

for Manual Transmission
  1. The ECM detects the shift change status from the neutral position switch signal, and detects the current selected gear from the engine speed and vehicle speed. If the neutral position switch signal and the shift change status cannot be coordinated, the ECM interprets this as a malfunction, illuminates the MIL, and stores the DTC.
for Automatic Transmission
  1. If the ECM cannot coordinate the N, P or neutral information from the park/neutral position switch signal with the shift information sent from the TCM through CAN communication, then the ECM interprets this as a malfunction, illuminates the MIL, and stores the DTC.

CONFIRMATION DRIVING PATTERN



  1. A283034E02


  2. A283035E04

  3. Connect the GTS to the DLC3.
  4. Turn the ignition switch to ON and turn the GTS on.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Turn the ignition switch to ON and turn the GTS on.
  8. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
  9. Change gear position 3 times or more during Accelerating vehicle to 64 km/h (40 mph) [A]. (for Manual Transmission)

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B]. (for Automatic Transmission)

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  11. Enter the following menus: Powertrain / Engine / Trouble Codes.
  12. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  14. Input the DTC: P0851 or P0852.
  15. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  16. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A280098E01


A280656E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Stop light switch assembly conditions can be checked using the GTS.
    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch and ST1.
    5. Check the Data List indication when the brake pedal is depressed and released.

      Brake Pedal Operation
      Stop Light Switch
      ST1
      Depressed
      ON
      ON
      Released
      OFF
      OFF

1.CHECK VEHICLE TYPE
  1. Confirm the transmission.

    Result 
    Result
    Proceed to
    for Manual Transmission
    A
    for Automatic Transmission
    B



B
Go to step 5
A


2.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF NEUTRAL POSITION SWITCH)


    A280103E01
  1. Disconnect the neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A54-1 - A54-2
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Neutral Position Switch)



NG
Go to step 4
OK


3.INSPECT NEUTRAL POSITION SWITCH
  1. Inspect the neutral position switch (Click here).



NG
REPLACE NEUTRAL POSITION SWITCH (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK HARNESS AND CONNECTOR (NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-16 (NSW) - A54-2
    Always
    Below 1 Ω
    A33-4 (EC) - A54-1
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-16 (NSW) or A54-2 - Body ground
    Always
    10 kΩ or higher
    A33-4 (EC) or A54-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)


    A280097E01
  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L2-4 - L2-5
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch Assembly)



NG
Go to step 7
OK


6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-16 (NSW) - L2-4
    Always
    Below 1 Ω
    L2-5 - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-16 (NSW) or L2-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)