Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1246    Master Cylinder Pressure Sensor Malfunction

for Preparation Click here


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

C210263E01


DTC No.
DTC Detection Condition
Trouble Area
C1246
Any of the following is detected:
  1. The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).
  2. An abnormality is detected in the skid control ECU internal sensor test.
  3. The sensor signal offset value is out of range.
  1. STOP fuse
  2. Stop light switch circuit
  3. Master cylinder pressure sensor circuit
  4. Master cylinder pressure sensor (Brake actuator assembly)

WIRING DIAGRAM

Refer to DTCs C1249 .

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)
OK


2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Master Cylinder Sensor
    Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V
    Brake pedal released: 0.20 to 0.40 V
    Reading increases when brake pedal is depressed

  1. Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

    OK:
    When the pedal is depressed, the voltage displayed on the GTS increases.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


3.READ VALUE USING GTS (STOP LIGHT SWITCH)
  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the GTS change according to brake pedal operation.

    OK:
    The GTS displays on or off according to brake pedal operation.



NG
Go to step 5
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1246 is not output.
    A
    DTC C1246 is output.
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C261872E01
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the noise filter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A13-3 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Noise Filter)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6.INSPECT NOISE FILTER
  1. Remove the noise filter (Click here).

  1. Inspect the noise filter (Click here).



NG
REPLACE NOISE FILTER (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-2 - A22-1
    Always
    Below 1 Ω
    A13-1 - A22-2
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C261861E01
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A5-30 (STP) - Body ground
    Stop light switch ON (Brake pedal depressed)
    11 to 14 V*
    Stop light switch OFF (Brake pedal released)
    Below 1.5 V

    HINT:
    *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)