ENTRY AND START SYSTEM (for Entry Function) > Room Oscillator does not Recognize Key |

| 1.CHECK ENTRY AND START SYSTEM (FOR ENTRY FUNCTION) |
Check that the entry lock and unlock functions operate for each door (Click here).
|
| ||||
| OK | |
| 2.CHECK ENTRY AND START SYSTEM (FOR START FUNCTION) |
Remove the battery of the electrical key transmitter sub-assembly (Click here).
![]() |
With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch as shown in the illustration.
When operating the engine switch, check whether the engine starts.
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly (w/o Panic Switch) |
| *3 | Electrical Key Transmitter Sub-assembly (w/ Panic Switch) |
| *4 | Electrical Key Transmitter Sub-assembly |
| *A | Type A |
| *B | Type B |
|
| ||||
| OK | |
| 3.CHECK WAVE ENVIRONMENT |
Install the battery to the electrical key transmitter sub-assembly (Click here).
Bring the electrical key transmitter sub-assembly near the indoor electrical key oscillator (front floor), and check that the engine can be started.
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key oscillator (rear floor), and check that the engine can be started*.
|
| ||||
| OK | ||
| ||
| 4.CHECK KEY DIAGNOSTIC MODE |
Check the following antennas in the key diagnostic mode (Click here).
![]() |
Check the indoor electrical key oscillator (front floor).
| *1 | Electrical Key Transmitter Sub-assembly |
| *a | Inspection point |
![]() |
Check the No. 2 indoor electrical key oscillator (rear floor).
| *1 | Electrical Key Transmitter Sub-assembly |
| *a | Inspection point |
| Result | Proceed to |
| Front side operation fails | A |
| rear floor operation fails | B |
| Front and rear operation checks are normal | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) - INDOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the D41 certification ECU (smart key ECU assembly) connector.
Disconnect the D26 indoor electrical key oscillator (front floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D41-3 (CLG5) - D26-1 (ANTE5) | Always | Below 1 Ω |
| D41-2 (CG5B) - D26-3 (CLGB) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D41-3 (CLG5) or D26-1 (ANTE5) - Body ground | Always | 10 kΩ or higher |
| D41-2 (CG5B) or D26-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR)) |
![]() |
Reconnect the D41 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector (to Indoor Electrical Key Oscillator (front floor)) |
| *b | Waveform |
| *c | Door is open and then closed for 30 seconds |
| *d | From approximately 30 seconds after door is closed |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
| D26-1 (ANTE5) - D26-3 (CLGB) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
|
| ||||
| OK | |
| 7.REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR) |
Temporarily replace the indoor electrical key oscillator (front floor) with a new or normally functioning one (Click here).
| NEXT | |
| 8.CHECK KEY DIAGNOSTIC MODE |
Check the following antenna in the key diagnostic mode (Click here).
![]() |
Check the indoor electrical key oscillator (front floor).
| *1 | Electrical Key Transmitter Sub-assembly |
| *a | Inspection point |
|
| ||||
| OK | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) - NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the D40 certification ECU (smart key ECU assembly) connector.
Disconnect the H15 No. 2 indoor electrical key oscillator (rear floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D40-11 (CLG6) - H15-1 (ANTE6) | Always | Below 1 Ω |
| D40-10 (CG6B) - H15-3 (CLGB) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D40-11 (CLG6) or H15-1 (ANTE6) - Body ground | Always | 10 kΩ or higher |
| D40-10 (CG6B) or H15-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR) |
![]() |
Reconnect the D40 certification ECU (smart key ECU assembly) connector.
| *a | Front view of wire harness connector (to No. 2 Indoor Electrical Key Oscillator (rear floor)) |
| *b | Waveform |
| *c | Door is open and then closed for 30 seconds |
| *d | From approximately 30 seconds after door is closed |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
| H15-1 (ANTE6) - H15-3 (CLGB) | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
|
| ||||
| OK | |
| 11.REPLACE NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR (REAR FLOOR) |
| NEXT | |
| 12.CHECK KEY DIAGNOSTIC MODE |
Check the following antenna in the key diagnostic mode (Click here).
![]() |
Check the No. 2 indoor electrical key oscillator (rear floor).
| *1 | Electrical Key Transmitter Sub-assembly |
| *a | Inspection point |
|
| ||||
| OK | ||
| ||