Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

ENTRY AND START SYSTEM (for Start Function) > Power Source Mode does not Change to ON (IG and ACC)

for Preparation Click here


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
  1. With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
  2. When the transmitter battery in the electrical key transmitter sub-assembly is depleted, touch the electrical key transmitter sub-assembly to the surface of the engine switch while depressing the brake pedal*1 or clutch pedal*2.
  3. When the entry cancel function is set by customize operation, touch the electrical key transmitter sub-assembly to the surface of the engine switch while depressing the brake pedal*1 or clutch pedal*2.
    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

HINT:
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


Related Data List and Active Test Items 
Problem Symptom
Data List Item
Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
  1. Start Switch1
  2. Start Switch2
  3. Latch Circuit
  4. IG1 Relay Monitor(Outside)
  5. IG1 Relay Monitor(Inside)
  6. IG2 Relay Monitor(Outside)
  7. IG2 Relay Monitor(Inside)
  8. ACC Relay Monitor
  9. Power Supply Condition
Engine
  1. Ignition Status
-

WIRING DIAGRAM


B314087E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
  5. If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).
  6. After completing repairs, confirm that the problem does not reoccur.
  7. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM (OPERATION)
  1. Check that the wireless door lock function operates normally (Click here).

OK:
Wireless door lock functions operate normally.



NG
GO TO ENTRY AND START SYSTEM (ALL DOOR ENTRY LOCK/UNLOCK FUNCTIONS AND WIRELESS FUNCTIONS DO NOT OPERATE) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E18
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


3.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of harness connected
    (to Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK ENTRY AND START SYSTEM
  1. Remove the battery of the electrical key transmitter sub-assembly (Click here).



    B375169E01
  1. With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch as shown in the illustration.

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

  1. When touch the logo of the electrical key transmitter sub-assembly to the engine switch, check whether the power source mode changes.

    OK:
    Power source mode changes.

    HINT:
    If the power source mode changes, the cabin verification is malfunctioning.

    Result 
    Result
    Proceed to
    NG (Power source mode does not change)
    A
    OK (Power source mode changes)
    B
    Text in Illustration 
    *1
    Engine Switch
    *2
    Electrical Key Transmitter Sub-assembly (w/o Panic Switch)
    *3
    Electrical Key Transmitter Sub-assembly (w/ Panic Switch)
    *4
    Electrical Key Transmitter Sub-assembly
    *A
    Type A
    *B
    Type B



B
Go to step 13
A


5.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/CLUTCH SW)
  1. for Automatic Transmission

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. According to the display on the GTS tester, read the Data List.

      Power Source Control 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Stop Light Switch1
      State of brake pedal / OFF or ON
      OFF: Brake pedal released
      ON: Brake pedal depressed
      1. Use this item to determine whether the stop light switch is malfunctioning.
      2. The engine cannot be started when this item is "OFF".
      3. When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.

      OK:
      ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen according to the stop light switch condition.

  1. for Manual Transmission

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. According to the display on the GTS, read the Data List.

      Power Source Control 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Neutral SW / Clutch SW
      State of clutch pedal / OFF or ON
      OFF: Clutch pedal released
      ON: Clutch pedal depressed
      1. Use this item to help determine if the clutch switch is malfunctioning.
      2. The engine cannot be started when this item is "OFF".

      OK:
      ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the stop light switch condition.

      Result 
      Result
      Proceed to
      OK
      A
      NG (for Automatic Transmission)
      B
      NG (for Manual Transmission)
      C



B
Go to step 8

C
Go to step 10
A


6.READ VALUE USING GTS (POWER SUPPLY CONDITION)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power Supply Condition / All OFF, IG1 ON or ACC ON, IG2 ON, ST ON,
    All OFF: Engine switch off (ACC and IG)
    ACC ON: Engine switch on (ACC))
    IG1 ON: Engine switch on (IG) (IG1 relay on)
    IG2 ON: Engine switch on (IG) (IG2 relay on)
    ST ON: Sending engine start request signal
    Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).

    OK:
    Display changes according to the changes in the power source mode when the engine switch is pushed.



NG
Go to step 12
OK


7.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power Supply Condition / All OFF, IG ON or ACC ON, IG2 ON, ST ON,
    All OFF: Engine switch off (ACC and IG)
    ACC ON: Engine switch on (ACC))
    IG1 ON: Engine switch on (IG) (IG1 relay on)
    IG2 ON: Engine switch on (IG) (IG2 relay on)
    ST ON: Sending engine start request signal
    Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).



  1. Measure the voltage according to the value(s) in the table below.


    B264896E21


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (IG1D) - Body ground
    Engine switch off
    1 V or less
    Engine switch on (ACC)
    1 V or less
    Engine switch on (IG)
    9 V or higher
    D48-9 (IG2D) - Body ground
    Engine switch off
    1 V or less
    Engine switch on (ACC)
    1 V or less
    Engine switch on (IG)
    9 V or higher
    D41-4 (ACCD) - Body ground
    Engine switch off
    1 V or less
    Engine switch on (ACC)
    8.5 V or higher
    Engine switch on (IG)
    8.5 V or higher



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

CHECK RELAY CONTACT SIDE CIRCUIT 

8.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Remove the stop light switch assembly (Click here).

  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (NOISE FILTER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A13 noise filter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-18 (STP1) - A13-4
    Always
    Below 1 Ω
    D48-18 (STP1) - Body ground
    Always
    10 kΩ or higher



    B269097E05
  1. Reconnect the A13 noise filter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-18 (STP1) - Body ground
    Brake pedal released
    Below 1 V
    Brake pedal depressed
    9 V or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (Certification ECU (Smart Key ECU Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

10.INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Remove the clutch start switch assembly.

    1. for LHD (Click here)
    2. for RHD (Click here)

  1. Inspect the clutch start switch assembly.

    1. for LHD (Click here)
    2. for RHD (Click here)

Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
A


11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
B268617E06
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A20 clutch start switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D48-10 (CLUT) - A20-2
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D48-10 (CLUT) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A20 clutch start switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-10 (CLUT) - Body ground
    Clutch pedal released → clutch pedal depressed
    Below 1 V → 9 V or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to certification ECU (smart key ECU assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

12.CHECK FOR DTC
  1. Check the DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC B2784 is output
    B
    DTC B2785 is output
    C



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (B2784) (Click here)

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (B2785) (Click here)
A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY 

13.READ VALUE USING GTS (START SWITCH 1, 2)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the GTS, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch 1
    Condition of engine switch contact 1 / OFF or ON
    OFF: Engine switch not pushed
    ON: Engine switch pushed
    1. If the engine switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the engine switch input signal is malfunctioning.
    Start Switch 2
    Condition of engine switch contact 2 / OFF or ON
    OFF: Engine switch not pushed
    ON : Engine switch pushed
    1. Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.
    2. Behaves the same way as engine switch 1.

    OK:
    The ECU data monitor changes in response to the operation of the engine switch.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
GO TO ENTRY AND START SYSTEM (FOR ENTRY FUNCTION) (ROOM OSCILLATOR DOES NOT RECOGNIZE KEY) (Click here)
A


14.INSPECT ENGINE SWITCH
  1. Remove the engine switch (Click here).

  1. Inspect the engine switch (Click here).



NG
REPLACE ENGINE SWITCH (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the D25 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D41-28 (SSW1) - D25-5 (SSW1)
    Always
    Below 1 Ω
    D41-30 (SSW2) - D25-1 (SSW2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D41-28 (SSW1) or D25-5 (SSW1) - Body ground
    Always
    10 kΩ or higher
    D41-30 (SSW2) or D25-1 (SSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)