Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry door lock and unlock functions and the wireless door lock and unlock functions do not operate, radio wave interference, or a malfunction in the key or signal circuit between the door control receiver and certification ECU (smart key ECU assembly) is suspected. The signal circuit is shared by the entry function and wireless door lock function.

WIRING DIAGRAM


B312716E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  5. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  6. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  7. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  8. After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".
  9. Door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".

1.CHECK BATTERY VOLTAGE
  1. Measure the voltage of the vehicle battery.

    Standard voltage:
    11 to 14 V

    HINT:
    It may be possible to tell whether the vehicle battery is discharged by operating the horn.
    If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.


NEXT


2.CHECK FOR DTC
  1. Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.

  1. Connect the GTS and check for DTCs (Click here).

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


3.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


4.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
  1. Check if there are any other registered electrical key transmitter sub-assemblies.
    Result 
    Result
    Proceed to
    There are no other registered electrical key transmitter sub-assemblies
    A
    There is another registered electrical key transmitter sub-assemblies
    B



B
Go to step 6
A


5.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
  1. Register a new electrical key transmitter sub-assembly (Refer to the Service Bulletin).


NEXT


6.CHECK ENTRY DOOR LOCK OPERATION
  1. Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

    OK:
    Entry lock/unlock operate normally.



NG
Go to step 9
OK


7.CHECK TRANSMITTER BATTERY
  1. Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

    1. Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
      Result 
      Result
      Proceed to
      Transmitter LED does not illuminate when switch is pressed and held
      A
      Transmitter LED illuminates 3 times or more when switch is pressed and held
      B
      Transmitter LED illuminates once or twice but not a third time
      C

      HINT:
      1. The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.4 V or less (Click here)
      2. Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.



B
REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C
REPLACE TRANSMITTER BATTERY (Click here)
A


8.INSPECT TRANSMITTER BATTERY (VOLTAGE)
  1. Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (Click here).



    B375170E01
  1. Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
    Text in Illustration 
    *1
    Lead Wire
    *A
    Type A
    *B
    Type B

    NOTICE:
    Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    B375171E01
  1. Measure the voltage of the transmitter battery.
    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *a
    GND

    HINT:
    1. When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.
    2. Perform the measurement when the key is at room temperature.
    3. The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.4 V or less the Data List item "Key Low Battery" displays "Yes". (Click here)

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Transmitter battery positive (+) - Transmitter battery negative (-)
    Engine switch off, all doors closed and lock sensor touched
    2.5 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY 

9.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
    3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
    4. If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

    OK:
    Wireless and entry functions operate normally.



NG
Go to step 10
OK

AFFECTED BY WAVE INTERFERENCE 

10.READ VALUE USING GTS (ACC SW, IG SW)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the GTS, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Engine switch on (ACC) / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (ACC)
    -
    IG SW
    Engine switch on (IG) / OFF or ON
    OFF: Engine switch off
    ON: Engine switch on (IG)
    -



NG
TROUBLESHOOT MAIN BODY ECU (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)


    B274828E06
  1. Disconnect the D48 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D48-2 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))

  1. Reconnect the D48 certification ECU (smart key ECU assembly) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
  1. Disconnect the D40 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H26 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D40-5 (RCO) - H26-4 (+5)
    Always
    Below 1 Ω
    D40-17 (RDA) - H26-5 (DATA)
    Always
    Below 1 Ω
    D40-19 (RSSI) - H26-2 (RSSI)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D40-5 (RCO) or H26-4 (+5) - Body ground
    Always
    10 kΩ or higher
    D40-17 (RDA) or H26-5 (DATA) - Body ground
    Always
    10 kΩ or higher
    D40-19 (RSSI) or H26-2 (RSSI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT DOOR CONTROL RECEIVER
  1. Reconnect the H26 door control receiver connector.



    B274836E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H26-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control Receiver)



NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK


14.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the D40 certification ECU (smart key ECU assembly) connector.



    B274836E62
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H26-4 (+5) - H26-1 (GND)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly switch not pressed
    Below 1 V
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly switch pressed
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control Receiver)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


15.INSPECT DOOR CONTROL RECEIVER


    B274836E27
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H26-2 (RSSI) - H26-1 (GND)
    Procedure:
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch not pressed
    11 to 14 V
    Procedure:
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch pressed
    Below 2 V
    H26-5 (DATA) - H26-1 (GND)
    Procedure:
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch not pressed
    11 to 14 V
    1. All doors closed
    2. All doors locked
    3. Electrical key transmitter sub-assembly switch pressed
    11 to 14 V → Below 2 V → 11 to 14 V pulse generation output at regular interval

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control Receiver)



NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK


16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    NOTICE:
    When the certification ECU (smart key ECU assembly) is replaced, it is also necessary to replace all registered electrical key transmitter sub-assemblies.


NEXT


17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check that the wireless door lock functions operate normally (Click here).

    OK:
    Wireless door lock functions operate normally.



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)