Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Rear Fog Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch assembly information signals, and illuminates the rear fog light.

WIRING DIAGRAM


E252208E01


INSPECTION PROCEDURE

HINT:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

1.CHECK OPERATION (TAILLIGHT)
  1. Check the operation of the taillight.

    OK:
    The taillight operates normally.



NG
GO TO TAILLIGHT (Click here)
OK


2.PERFORM ACTIVE TEST USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check that the relay operates.


Main Body 
Tester Display
Test Part
Control Range
Diagnostic Note
Rear Fog Light Relay
Rear fog light relay
ON/OFF
Light control switch is in TAIL position

OK:
Rear fog light relay operates (Rear fog lights come on).



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

3.INSPECT RR FOG RELAY
  1. Remove the RR FOG relay from the engine room relay block.

  1. Inspect the RR FOG relay (Click here).



NG
REPLACE RR FOG RELAY
OK


4.INSPECT REAR FOG LIGHT BULB (REAR LIGHT ASSEMBLY)
  1. Remove the rear fog light bulb (Click here).

  1. Inspect the rear fog light bulb (Click here).



NG
REPLACE REAR FOG LIGHT BULB (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (BATTERY - RR FOG RELAY)
  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
Relay terminal 2 - Body ground
Light control switch off → tail
Below 1 V → 11 to 14 V
Relay terminal 5 - Body ground
Always
11 to 14 V



NG
Go to step 8
OK


6.CHECK HARNESS AND CONNECTOR (RR FOG RELAY - REAR LIGHT ASSEMBLY)
  1. Disconnect the H2 rear light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
Relay terminal 3 - H2-2
Light control switch off → tail
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
Relay terminal 3 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (RR FOG RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the A73 instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
Relay terminal 1 - A73-3
Always
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
Relay terminal 1 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).



  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


    E219837E04


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Measure the voltage according to the value(s) in the table below.


Standard Voltage:

Tester Connection
Condition
Specified Condition
3C-26 - Battery negative (-) terminal
Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY)
11 to 14 V



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)