Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0201    Injector Circuit / Open - (Cylinder 1)

DTC    P0202    Injector Circuit / Open - (Cylinder 2)

DTC    P0203    Injector Circuit / Open - (Cylinder 3)

DTC    P0204    Injector Circuit / Open - (Cylinder 4)

for Preparation Click here


DESCRIPTION

The D-4S system has two injection systems. One is the in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is the intake port injection system. The ECM determines the percentage of in-cylinder direct injection to the intake port injection systems in accordance with the engine speed and load.

DTC No.
DTC Detection Condition
Trouble Area
P0201
Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 1 cylinder).
(1 trip detection logic)
  1. Open or short in fuel injector (for port injection) circuit (No. 1 cylinder)
  2. INJ fuse
  3. Fuel injector assembly (for port injection) (No. 1 cylinder)
  4. ECM
P0202
Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 2 cylinder).
(1 trip detection logic)
  1. Open or short in fuel injector (for port injection) circuit (No. 2 cylinder)
  2. INJ fuse
  3. Fuel injector assembly (for port injection) (No. 2 cylinder)
  4. ECM
P0203
Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 3 cylinder).
(1 trip detection logic)
  1. Open or short in fuel injector (for port injection) circuit (No. 3 cylinder)
  2. INJ fuse
  3. Fuel injector assembly (for port injection) (No. 3 cylinder)
  4. ECM
P0204
Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 4 cylinder).
(1 trip detection logic)
  1. Open or short in fuel injector (for port injection) circuit (No. 4 cylinder)
  2. INJ fuse
  3. Fuel injector assembly (for port injection) (No. 4 cylinder)
  4. ECM

MONITOR DESCRIPTION

The ECM monitors the injection control of the port injector. If a malfunction is detected in the port injector circuit, the ECM cancels the injection control for the corresponding cylinder and turns on the MIL.

CONFIRMATION DRIVING PATTERN



  1. A283032E01

  2. Connect the GTS to the DLC3.
  3. Turn the ignition switch to ON and turn the GTS on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the GTS on.
  7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
  8. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].
  9. Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Enter the following menus: Powertrain / Engine / Trouble Codes.
  11. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  13. Input the DTC: P0201, P0202, P0203 or P0204.
  14. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  15. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A280104E01


INSPECTION PROCEDURE

HINT:
  1. If DTC P0201 is output, check the No. 1 fuel injector assembly (for port injection) (No. 1 cylinder) circuit.
  2. If DTC P0202 is output, check the No. 2 fuel injector assembly (for port injection) (No. 2 cylinder) circuit.
  3. If DTC P0203 is output, check the No. 3 fuel injector assembly (for port injection) (No. 3 cylinder) circuit.
  4. If DTC P0204 is output, check the No. 4 fuel injector assembly (for port injection) (No. 4 cylinder) circuit.
  5. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    P0201, P0202, P0203 and P0204 are output
    A
    P0201, P0202, P0203 or P0204 is output
    B
    P0201, P0202, P0203 or P0204 and other DTCs are output
    C



B
Go to step 5

C
GO TO DTC CHART (Click here)
A


2.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE VOLTAGE)


    A280161E01
  1. Disconnect the fuel injector assembly (for port injection) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C8-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C30-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C31-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)
    *b
    No. 1 cylinder
    *c
    No. 2 cylinder
    *d
    No. 3 cylinder
    *e
    No. 4 cylinder



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION))
  1. Disconnect the ECM connector.

  1. Disconnect the fuel injector assembly (for port injection) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A36-12 (#10) - C8-2
    Always
    Below 1 Ω
    A36-22 (#20) - C30-2
    Always
    Below 1 Ω
    A36-32 (#30) - C9-2
    Always
    Below 1 Ω
    A36-13 (#40) - C31-2
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A36-12 (#10) or C8-2 - Body ground
    Always
    10 kΩ or higher
    A36-22 (#20) or C30-2 - Body ground
    Always
    10 kΩ or higher
    A36-32 (#30) or C9-2 - Body ground
    Always
    10 kΩ or higher
    A36-13 (#40) or C31-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Inspect the fuel injector assembly (for port injection) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
OK

REPLACE ECM (Click here)  

5.INSPECT RELAY (EFI MAIN1)
  1. Inspect the EFI MAIN1 relay .



NG
REPLACE RELAY (EFI MAIN1)
OK


6.CHECK HARNESS AND CONNECTOR (EFI MAIN1 RELAY - FUEL INJECTOR ASSEMBLY)
  1. Disconnect the fuel injector assembly (for port injection) connector.

  1. Remove the EFI MAIN1 relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    C8-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω
    C30-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω
    C9-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω
    C31-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    C8-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C30-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C9-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C31-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)