Home › Drivetrain · TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > Shift Paddle Switch Circuit

for Preparation Click here


DESCRIPTION

When the shift lever is in M, it is possible to change into any gear using the steering assembly transmission shift switch.
Additionally, when the vehicle is being driving with the shift lever in D, operating the steering assembly transmission shift switch changes to selection of gears with the shift lever in D, enabling shifting to any gear.

WIRING DIAGRAM


C259540E04


INSPECTION PROCEDURE

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Read the value displayed on the GTS.
    OK 
    Tester Display
    Condition
    Standard
    Sport Shift Up SW
    Continuously shift to "+" (upshift): ON
    Release "+" (up-shift): OFF
    -
    Sport Shift Down SW
    Continuously shift to "-" (down-shift): ON
    Release "-" (down-shift): OFF
    -



NG
Go to step 2
OK

CHECK INTERMITTENT PROBLEMS (Click here)  

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT SWITCH ASSEMBLY - TCM)
  1. Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-1(SFTD) - Body ground
    Pull continuously
    "+"
    (Up shift)
    Below 1 Ω
    Release "+" or "-"
    10 kΩ or higher
    A19-2(SFTU) - Body ground
    Pull continuously
    "-"
    (Down shift)
    Below 1 Ω
    Release "+" or "-"
    10 kΩ or higher

  1. Connect the TCM connector.



NG
Go to step 4
OK


3.REPLACE TCM
  1. Replace the TCM (Click here).


NEXT

PERFORM THE RESET MEMORY (Click here)  

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D77-2 - Body ground
    Always
    Below 1 Ω

  1. Connect the spiral cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM)
  1. Disconnect the TCM connector.

  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-1(SFTD) - D77-8
    Always
    Below 1 Ω
    A19-2(SFTU) - D77-1
    Always
    Below 1 Ω
    A19-1(SFTD) or D77-8 - Body ground
    Always
    10 kΩ or higher
    A19-2(SFTU) or D77-1 - Body ground
    Always
    10 kΩ or higher

  1. Connect the TCM connector.

  1. Connect the spiral cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TRANSMISSION SHIFT SWITCH ASSEMBLY (TRANSMISSION SHIFT SWITCH ASSEMBLY - SPIRAL CABLE)
  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z4-1 - z4-4
    Pull continuously
    "+"
    (Up shift)
    Below 1 Ω
    Release "+" or "-"
    10 kΩ or higher
    z4-3 - z4-4
    Pull continuously
    "-"
    (Down shift)
    Below 1 Ω
    Release "+" or "-"
    10 kΩ or higher

  1. Connect the spiral cable sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY
  1. Inspect the transmission shift switch assembly (Click here).



NG
REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY (Click here)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)