Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Tachometer Malfunction

for Preparation Click here


DESCRIPTION

The combination meter assembly controls the tachometer in accordance with the engine speed signals from the ECM through the CAN communication system.

WIRING DIAGRAM


E140490E46


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTCs are not output
    A
    DTCs are output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tachometer Operation
    Tachometer
    0, 1000, 2000, 3000, , 4000, 5000, 6000, 7000 rpm
    -

    OK:
    The engine speed displayed on the tester is approximately the same as that of the tachometer reading.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.READ VALUE USING GTS (ENGINE RPM)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. According to the display on the tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Rpm
    Engine speed
    Min.: 0
    Max.: 12750
    Approximately same as actual engine speed (when engine is running)
    Unit: rpm

    OK:
    The engine speed displayed on the tester is approximately the same as that displayed on the combination meter assembly.

    NOTICE:
    Determine whether the value displayed on the tester is within the acceptable range by referring to the reference values described in "On-Vehicle Inspection" (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.CHECK SFI SYSTEM
  1. Check if the SFI system outputs DTCs (Click here).
    Result 
    Result
    Proceed to
    DTCs are not output
    A
    DTCs are output
    B



B
GO TO SFI SYSTEM (Click here)
A


5.READ VALUE USING GTS (ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List.

  1. According to the display on the tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Speed
    Engine speed
    Min.: 0
    Max.: 16383.75
    Approximately same as actual engine speed (when engine is running)
    Unit: rpm

    OK:
    The engine speed displayed on the tester is approximately the same as that displayed on the combination meter assembly.

    NOTICE:
    Determine whether the value displayed on the tester is within the acceptable range by referring to the reference values described in "On-Vehicle Inspection" (Click here).



NG
GO TO SFI SYSTEM (Click here)
OK


6.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or a normal one (Click here).

OK:
The operation of the tachometer returns to normal.



NG
REPLACE ECM (Click here)
OK

END