Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1627    Side Airbag Sensor LH Lost Communication

DTC    B1628    Side Airbag Sensor LH Initialization

DTC    B1637    Side No. 2 Airbag Sensor LH Lost Communication

DTC    B1638    Side No. 2 Airbag Sensor LH Initialization

DTC    B1647    Side Satellite Sensor Bus Lost Communication (LH)

DTC    B1697    Lost Communication with Side Airbag Sensor LH

DTC    B1698    Side Airbag Sensor LH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag ECU assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and rear airbag sensor LH and No. 2 airbag sensor assembly.
The side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected for the side collision sensor LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1627
B1628
B1637
B1638
B1647
B1697
B1698
  1. The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit.
  2. Side airbag sensor assembly LH malfunction
  3. Side No. 2 airbag sensor assembly LH malfunction
  4. Rear airbag sensor LH malfunction
  5. Airbag ECU assembly malfunction
  1. Floor wire
  2. Front door wire LH
  3. Side airbag sensor assembly LH
  4. Side No. 2 airbag sensor assembly LH
  5. Rear airbag sensor LH
  6. Airbag ECU assembly

WIRING DIAGRAM


C238366E16


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1647 is output.
    A
    Current DTC B1628 or B1638 is output.
    B
    Current DTC B1697 or B1698 is output.
    C
    Current DTC B1627 or B1637 is output.
    D
    Current DTCs B1627, B1628, B1637, B1638, B1647, B1697 and B1698 are not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.
    2. Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1697 and B1698 may be output at this time, but they are not related to this check.



B
Go to step 18

C
Go to step 33

D
Go to step 40

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and rear airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and rear airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK FLOOR WIRE (OPEN)


    C238225E13
  1. Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) -H23-3 (RTNIN)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT)


    C238226E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - H23-3 (RTNIN)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO B+)


    C238226E12
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - Body ground
    Ignition switch ON
    Below 1 V
    H23-3 (RTNIN) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT TO GROUND)


    C238226E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - Body ground
    Always
    1 MΩ or higher
    H23-3 (RTNIN) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


7.CHECK FLOOR WIRE (OPEN)


    C238392E15
  1. Using a service wire, connect terminals 4 (BUSIN) and 3 (RTNIN) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - H23-2 (RTNOUT)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)
    *b
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
REPLACE FLOOR WIRE
OK


8.CHECK FLOOR WIRE (SHORT)
C238222E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - H23-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


9.CHECK FLOOR WIRE (SHORT TO B+)


    C238222E19
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    H23-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


10.CHECK FLOOR WIRE (SHORT TO GROUND)


    C238222E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    H23-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (OPEN)


    C238393E10
  1. Connect the connectors that link the floor wire and front door wire LH.

  1. Using a service wire, connect terminals 2 (BUSIN) and 1 (RTNIN) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - H25-2 (RTNOUT)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
Go to step 43
OK


12.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (SHORT)


    C238394E10
  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - H25-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
Go to step 44
OK


13.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (SHORT TO B+)


    C238394E10
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    H25-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
Go to step 45
OK


14.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (SHORT TO GROUND)


    C238394E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    H25-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
Go to step 46
OK


15.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    C238224E01
  1. Connect the connectors to the rear airbag sensor LH, side airbag sensor assembly LH and airbag ECU assembly.

  1. Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1647 is output.
    A
    DTC B1642 is output.
    B
    DTCs B1642 and B1647 are not output.
    C

    HINT:
    Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


16.CHECK REAR AIRBAG SENSOR LH


    C238223E01
  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1647 is output.
    A
    DTC B1642 is output.
    B
    DTCs B1642 and B1647 are not output.
    C

    HINT:
    Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly LH



B
REPLACE REAR AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    C238395E01
  1. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1647 is output.
    A
    DTC B1642 is output.
    B
    DTCs B1642 and B1647 are not output.
    C

    HINT:
    Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor LH



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

18.CHECK HISTORY DTC
  1. Check for history DTCs (Click here).

    Result:
    Result
    Proceed to
    History DTCs B1627 and B1637 are not output.
    A
    History DTC B1627 is output.
    B
    History DTC B1637 is output.
    C

    HINT:
    Codes other than history DTCs B1627 and B1637 may be output at this time, but they are not related to this check.



B
Go to step 41

C
Go to step 42
A


19.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1628 is output.
    A
    Current DTC B1638 is output.
    B

    HINT:
    Codes other than current DTCs B1628 and B1638 may be output at this time, but they are not related to this check.



B
Go to step 26
A


20.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly and side No. 2 airbag sensor assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly and side No. 2 airbag sensor assembly LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


21.CHECK FLOOR WIRE (OPEN)


    C238225E13
  1. Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - H23-3 (RTNIN)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


22.CHECK FLOOR WIRE (SHORT)
C238226E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - H23-3 (RTNIN)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


23.CHECK FLOOR WIRE (SHORT TO B+)


    C238226E12
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - Body ground
    Ignition switch ON
    Below 1 V
    H23-3 (RTNIN) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


24.CHECK FLOOR WIRE (SHORT TO GROUND)


    C238226E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (BUSIN) - Body ground
    Always
    1 MΩ or higher
    H23-3 (RTNIN) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


25.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    C238224E01
  1. Connect the connector to the airbag ECU assembly.

  1. Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628 is output.
    A
    DTC B1623 is output.
    B
    DTCs B1623 and B1628 are not output.
    C

    HINT:
    Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

26.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the side No. 2 airbag sensor assembly LH and rear airbag sensor LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side No. 2 airbag sensor assembly LH and rear airbag sensor LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


27.CHECK FLOOR WIRE (OPEN)


    C238392E15
  1. Using a service wire, connect terminals 4 (BUSIN) and 3 (RTNIN) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - H23-2 (RTNOUT)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)
    *b
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
REPLACE FLOOR WIRE
OK


28.CHECK FLOOR WIRE (SHORT)
C238222E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - H23-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


29.CHECK FLOOR WIRE (SHORT TO B+)


    C238222E19
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    H23-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


30.CHECK FLOOR WIRE (SHORT TO GROUND)


    C238222E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    H23-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly LH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


31.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    C238224E01
  1. Connect the connector to the rear airbag sensor LH.

  1. Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1638 is output.
    A
    DTC B1633 is output.
    B
    DTCs B1633 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


32.CHECK REAR AIRBAG SENSOR LH


    C238223E01
  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1638 is output.
    A
    DTC B1633 is output.
    B
    DTCs B1633 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly LH



B
REPLACE REAR AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

33.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the rear airbag sensor LH and side airbag sensor assembly LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the rear airbag sensor LH and side airbag sensor assembly LH. Also disconnect the connectors that link the floor wire and front door wire LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


34.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (OPEN)


    C238393E10
  1. Connect the connectors that link the floor wire and front door wire LH.

  1. Using a service wire, connect terminals 2 (BUSIN) and 1 (RTNIN) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - H25-2 (RTNOUT)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
Go to step 43
OK


35.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (SHORT)


    C238394E10
  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - H25-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
Go to step 44
OK


36.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (SHORT TO B+)


    C238394E10
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    H25-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
Go to step 45
OK


37.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH CIRCUIT (SHORT TO GROUND)


    C238394E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H25-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    H25-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
Go to step 46
OK


38.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    C238395E01
  1. Connect the connectors to the rear airbag sensor LH.

  1. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1697 or B1698 is output.
    A
    DTC B1692 or B1693 is output.
    B
    DTCs B1692, B1693, B1697 and B1698 are not output.
    C

    HINT:
    Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor LH



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


39.CHECK REAR AIRBAG SENSOR LH


    C238223E01
  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1697 or B1698 is output.
    A
    DTC B1692 or B1693 is output.
    B
    DTCs B1692, B1693, B1697 and B1698 are not output.
    C

    HINT:
    Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly LH



B
REPLACE REAR AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

40.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1627 is output.
    A
    Current DTC B1637 is output.
    B

    HINT:
    Codes other than current DTCs B1627 and B1637 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.



B
Go to step 42
A


41.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH


    C238224E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1627 is output.
    A
    DTC B1622 is output.
    B
    DTCs B1622 and B1627 are not output.
    C

    HINT:
    Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

42.CHECK REAR AIRBAG SENSOR LH


    C238223E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1637 is output.
    A
    DTC B1632 is output.
    B
    DTCs B1632 and B1637 are not output.
    C

    HINT:
    Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly LH



B
REPLACE REAR AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

43.CHECK FRONT DOOR WIRE LH (OPEN)


    C238396E11
  1. Disconnect the front door wire LH connector from the floor wire.

    HINT:
    The service wire has already been inserted into connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EH1-1 - EH1-2
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *3
    Front Door Wire LH
    *4
    Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Floor Wire)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FRONT DOOR WIRE LH
OK

REPLACE FLOOR WIRE 

44.CHECK FRONT DOOR WIRE LH (SHORT)


    C238397E10
  1. Disconnect the front door wire LH connector from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EH1-1 - EH1-2
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *3
    Front Door Wire LH
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to Floor Wire)



NG
REPLACE FRONT DOOR WIRE LH
OK

REPLACE FLOOR WIRE 

45.CHECK FRONT DOOR WIRE LH (SHORT TO B+)
C238397E10
  1. Disconnect the front door wire LH connector from the floor wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    EH1-1 - Body ground
    Ignition switch ON
    Below 1 V
    EH1-2 - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *3
    Front Door Wire LH
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to Floor Wire)



NG
REPLACE FRONT DOOR WIRE LH
OK

REPLACE FLOOR WIRE 

46.CHECK FRONT DOOR WIRE LH (SHORT TO GROUND)


    C238397E10
  1. Disconnect the front door wire LH connector from the floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EH1-1 - Body ground
    Always
    1 MΩ or higher
    EH1-2 - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor LH
    *3
    Front Door Wire LH
    *4
    Floor Wire
    *a
    Front view of wire harness connector
    (to Floor Wire)



NG
REPLACE FRONT DOOR WIRE LH
OK

REPLACE FLOOR WIRE