Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1622    Side Airbag Sensor RH Lost Communication

DTC    B1623    Side Airbag Sensor RH Initialization

DTC    B1632    Side No. 2 Airbag Sensor RH Lost Communication

DTC    B1633    Side No. 2 Airbag Sensor RH Initialization

DTC    B1642    Side Satellite Sensor Bus Lost Communication (RH)

DTC    B1692    Lost Communication with Side Airbag Sensor RH

DTC    B1693    Side Airbag Sensor RH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH, rear airbag sensor RH and No. 2 airbag sensor assembly.
The side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1622
B1623
B1632
B1633
B1642
B1692
B1693
  1. The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.
  1. Side airbag sensor assembly RH malfunction
  2. Side No. 2 airbag sensor assembly RH malfunction
  3. Rear airbag sensor RH malfunction
  4. Airbag ECU assembly malfunction
  1. No. 2 floor wire
  2. Front door wire RH
  3. Side airbag sensor assembly RH
  4. Side No. 2 airbag sensor assembly RH
  5. Rear airbag sensor RH
  6. Airbag ECU assembly

WIRING DIAGRAM


C238366E15


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1642 is output.
    A
    Current DTC B1623 or B1633 is output.
    B
    Current DTC B1692 or B1693 is output.
    C
    Current DTC B1622 or B1632 is output.
    D
    Current DTCs B1622, B1623, B1632, B1633, B1642, B1692 and B1693 are not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.
    2. Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1692 and B1693 may be output at this time, but they are not related to this check.



B
Go to step 18

C
Go to step 33

D
Go to step 40

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and rear airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and rear airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238219E14
  1. Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - G16-3 (RTNIN)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK NO. 2 FLOOR WIRE (SHORT)


    C238220E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - G16-3 (RTNIN)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238220E11
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - Body ground
    Ignition switch ON
    Below 1 V
    G16-3 (RTNIN) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238220E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - Body ground
    Always
    1 MΩ or higher
    G16-3 (RTNIN) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


7.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238392E13
  1. Using a service wire, connect terminals 3 (RTNIN) and 4 (BUSIN) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - G16-2 (RTNOUT)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


8.CHECK NO. 2 FLOOR WIRE (SHORT)
C238222E18
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - G16-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238222E18
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    G16-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238222E18
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    G16-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


11.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)


    C238393E09
  1. Connect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Using a service wire, connect terminals 2 (BUSIN) and 1 (RTNIN) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - G14-2 (RTNOUT)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
Go to step 43
OK


12.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)


    C238394E09
  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - G14-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
Go to step 44
OK


13.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)


    C238394E09
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    G14-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
Go to step 45
OK


14.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)


    C238394E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    G14-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
Go to step 46
OK


15.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connectors to the rear airbag sensor RH, side airbag sensor assembly RH and airbag ECU assembly.

  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1642 is output.
    A
    DTC B1647 is output.
    B
    DTCs B1642 and B1647 are not output.
    C

    HINT:
    Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


16.CHECK REAR AIRBAG SENSOR RH


    C238223E01
  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1642 is output.
    A
    DTC B1647 is output.
    B
    DTCs B1642 and B1647 are not output.
    C

    HINT:
    Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly RH



B
REPLACE REAR AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


17.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238395E01
  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1642 is output.
    A
    DTC B1647 is output.
    B
    DTCs B1642 and B1647 are not output.
    C

    HINT:
    Codes other than DTCs B1642 and B1647 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor RH



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

18.CHECK HISTORY DTC
  1. Check for history DTCs (Click here).

    Result:
    Result
    Proceed to
    History DTCs B1622 and B1632 are not output.
    A
    History DTC B1622 is output.
    B
    History DTC B1632 is output.
    C

    HINT:
    Codes other than history DTCs B1622 and B1632 may be output at this time, but they are not related to this check.



B
Go to step 41

C
Go to step 42
A


19.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1623 is output.
    A
    Current DTC B1633 is output.
    B

    HINT:
    Codes other than current DTCs B1623 and B1633 may be output at this time, but they are not related to this check.



B
Go to step 26
A


20.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly and side No. 2 airbag sensor assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly and side No. 2 airbag sensor assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


21.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238219E15
  1. Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - G16-3 (RTNIN)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag ECU Assembly)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


22.CHECK NO. 2 FLOOR WIRE (SHORT)


    C238220E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - G16-3 (RTNIN)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238220E12
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - Body ground
    Ignition switch ON
    Below 1 V
    G16-3 (RTNIN) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238220E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-4 (BUSIN) - Body ground
    Always
    1 MΩ or higher
    G16-3 (RTNIN) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Airbag ECU Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


25.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connector to the airbag ECU assembly.

  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623 is output.
    A
    DTC B1628 is output.
    B
    DTCs B1623 and B1628 are not output.
    C

    HINT:
    Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

26.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the side No. 2 airbag sensor assembly RH and rear airbag sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side No. 2 airbag sensor assembly RH and rear airbag sensor RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


27.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238392E14
  1. Using a service wire, connect terminals 4 (BUSIN) and 3 (RTNIN) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - G16-2 (RTNOUT)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


28.CHECK NO. 2 FLOOR WIRE (SHORT)
C238222E17
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - G16-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


29.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238222E17
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    G16-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


30.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238222E17
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G16-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    G16-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


31.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connector to the rear airbag sensor RH.

  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1633 is output.
    A
    DTC B1638 is output.
    B
    DTCs B1633 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


32.CHECK REAR AIRBAG SENSOR RH


    C238223E01
  1. Interchange the rear airbag sensor RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1633 is output.
    A
    DTC B1638 is output.
    B
    DTCs B1633 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly RH



B
REPLACE REAR AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

33.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the rear airbag sensor RH and side airbag sensor assembly RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the rear airbag sensor RH and side airbag sensor assembly RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


34.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (OPEN)


    C238393E09
  1. Connect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Using a service wire, connect terminals 2 (BUSIN) and 1 (RTNIN) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - G14-2 (RTNOUT)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
Go to step 43
OK


35.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT)


    C238394E09
  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - G14-2 (RTNOUT)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
Go to step 44
OK


36.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT TO B+)


    C238394E09
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - Body ground
    Ignition switch ON
    Below 1 V
    G14-2 (RTNOUT) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
Go to step 45
OK


37.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH CIRCUIT (SHORT TO GROUND)


    C238394E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G14-1 (BUSOUT) - Body ground
    Always
    1 MΩ or higher
    G14-2 (RTNOUT) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *a
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
Go to step 46
OK


38.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238395E01
  1. Connect the connectors to the rear airbag sensor RH.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1692 or B1693 is output.
    A
    DTC B1697 or B1698 is output.
    B
    DTCs B1692, B1693, B1697 and B1698 are not output.
    C

    HINT:
    Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Rear Airbag Sensor RH



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


39.CHECK REAR AIRBAG SENSOR RH


    C238223E01
  1. Interchange the rear airbag sensor RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1692 or B1693 is output.
    A
    DTC B1697 or B1698 is output.
    B
    DTCs B1692, B1693, B1697 and B1698 are not output.
    C

    HINT:
    Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly RH



B
REPLACE REAR AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

40.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1622 is output.
    A
    Current DTC B1632 is output.
    B

    HINT:
    Codes other than current DTCs B1622 and B1632 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.



B
Go to step 42
A


41.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1622 is output.
    A
    DTC B1627 is output.
    B
    DTCs B1622 and B1627 are not output.
    C

    HINT:
    Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Airbag ECU Assembly



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

42.CHECK REAR AIRBAG SENSOR RH


    C238223E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 is output.
    A
    DTC B1637 is output.
    B
    DTCs B1632 and B1637 are not output.
    C

    HINT:
    Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly RH



B
REPLACE REAR AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG ECU ASSEMBLY (Click here)  

43.CHECK FRONT DOOR WIRE RH (OPEN)


    C238396E10
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

    HINT:
    The service wire has already been inserted into connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    FG1-1 - FG1-2
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

44.CHECK FRONT DOOR WIRE RH (SHORT)


    C238397E09
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    FG1-1 - FG1-2
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

45.CHECK FRONT DOOR WIRE RH (SHORT TO B+)


    C238397E09
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    FG1-1 - Body ground
    Ignition switch ON
    Below 1 V
    FG1-2 - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

46.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)


    C238397E09
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    FG1-1 - Body ground
    Always
    1 MΩ or higher
    FG1-2 - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Rear Airbag Sensor RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE