Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM J

FA20 ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit (low pressure side) is comprised of the ECM, fuel pump assembly (low pressure side), and fuel pump control ECU assembly (which operates the fuel pump [low pressure side]). The ECM judges the speed of the fuel pump assembly (low pressure side) based on the engine output. This speed is converted into a loading signal, which is sent to the fuel pump control ECU assembly. The fuel pump control ECU assembly adjusts the fuel pump operating speed (low pressure side), based on the signal sent from the ECM.

WIRING DIAGRAM

A280175E03
6.073,1.781 6.51,2.021 0.438,0.24 10 false IGSW 0.604,0.917 1.26,1.125 0.656,0.208 10 false IG2 MAIN 0.76,4.365 1.323,4.573 0.563,0.208 10 false F/PMP 2.115,4.51 2.729,4.76 0.615,0.25 10 false C/OPEN 4.427,0.927 4.781,1.146 0.354,0.219 10 false IG2 1.448,0.958 1.792,1.167 0.344,0.208 10 false AM2 1.375,1.698 2.479,2.156 1.104,0.458 10 false Ignition or Starter Switch Assembly 1.969,0.948 2.281,1.115 0.313,0.167 10 false IG2 3.469,1.354 3.833,1.583 0.365,0.229 10 false IG2 6.094,4.177 6.49,4.427 0.396,0.25 10 false DI 6.094,5.042 6.49,5.208 0.396,0.167 10 false FPC 2.01,6.365 3.448,6.729 1.438,0.365 10 false Fuel Pump Assembly 3.885,6.49 5.396,6.896 1.51,0.406 10 false Fuel Pump Control ECU Assembly 0.646,6.083 1.271,6.49 0.625,0.406 10 false Battery 5.719,1.781 6.073,2.01 0.354,0.229 10 false A33 5.76,1.583 5.99,1.771 0.229,0.188 10 false 27 5.729,4.167 6.063,4.323 0.333,0.156 10 false A35 5.729,5.042 6.021,5.188 0.292,0.146 10 false A35 5.76,3.979 6.021,4.177 0.26,0.198 10 false 10 5.76,4.833 5.99,5 0.229,0.167 10 false 19 1.375,1.531 1.708,1.688 0.333,0.156 10 false D55 1.927,3.771 2.115,3.969 0.188,0.198 10 false 2 2.688,3.76 2.875,3.948 0.188,0.188 10 false 1 1.927,4.094 2.146,4.313 0.219,0.219 10 false 5 2.688,4.104 2.854,4.292 0.167,0.188 10 false 3 3.188,0.677 3.406,0.927 0.219,0.25 10 false 5 3.917,0.667 4.115,0.844 0.198,0.177 10 false 3 3.188,0.979 3.365,1.167 0.177,0.188 10 false 2 1.281,0.99 1.385,1.135 0.104,0.146 10 false 7 3.917,0.979 4.115,1.188 0.198,0.208 10 false 1 2.906,2.938 5.01,3.448 2.104,0.51 10 false Certification ECU (Smart Key ECU Assembly) 2.51,0.979 2.781,1.177 0.271,0.198 10 false *2 0.552,7.125 3.833,7.479 3.281,0.354 10 false *1: w/ Entry and Start System 0.552,7.427 3.948,7.781 3.396,0.354 10 false *2: w/o Entry and Start System 1.969,2.406 2.208,2.604 0.24,0.198 10 false *1 2.927,1.573 3.208,1.771 0.281,0.198 10 false *1 3.875,6.313 4.271,6.469 0.396,0.156 10 false G12 2.01,6.198 2.333,6.365 0.323,0.167 10 false G7 2.052,5.865 2.24,6.031 0.188,0.167 10 false 4 3.021,5.865 3.271,6.094 0.25,0.229 10 false 3 3.708,5.865 3.875,6.031 0.167,0.167 10 false 6 3.719,4.969 3.906,5.146 0.188,0.177 10 false 5 3.729,4.083 3.896,4.271 0.167,0.188 10 false 1 4.792,4.063 5.01,4.26 0.219,0.198 10 false 3 4.792,4.938 4.99,5.115 0.198,0.177 10 false 2 4.781,5.854 4.99,6.042 0.208,0.188 10 false 4 2.906,2.771 3.281,2.99 0.375,0.219 10 false D48 0.604,1.229 1.271,1.438 0.667,0.208 10 false AM2 NO.1 0.635,2.677 1.344,2.917 0.708,0.24 10 false AM2 NO.2 3.156,2.385 3.333,2.583 0.177,0.198 10 false 2 3.167,1.969 3.385,2.167 0.219,0.198 10 false 9 2.26,0.979 2.469,1.177 0.208,0.198 10 false 6 6.229,6.01 6.615,6.25 0.385,0.24 10 false ECM 3.344,2.052 3.729,2.24 0.385,0.188 10 false IG2D 3.354,2.49 3.667,2.688 0.313,0.198 10 false +B 0.5,5.229 0.917,5.427 0.417,0.198 10 false MAIN 4.417,5.063 4.781,5.26 0.365,0.198 10 false FPC 4.521,4.188 4.771,4.427 0.25,0.24 10 false DI 4.583,5.938 4.792,6.146 0.208,0.208 10 false E 3.906,5.063 4.24,5.25 0.333,0.188 10 false FP- 3.896,5.969 4.24,6.167 0.344,0.198 10 false FP+ 3.896,4.177 4.25,4.385 0.354,0.208 10 false +B 2.698,5.969 3.021,6.135 0.323,0.167 10 false FP+ 2.208,5.969 2.542,6.125 0.333,0.156 10 false FP-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump/Speed.


e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

Result
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)

B

8.INSPECT FUEL PUMP CONTROL ECU ASSEMBLY (POWER SOURCE VOLTAGE)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)
a.

Connect the GTS to the DLC3.


A280167E03
0.76,1.854 1.469,1.302 true 2.688,1.854 1.969,1.302 true 0.542,1.875 1.115,2.073 0.573,0.198 10 false 3 (FP+) 2.594,1.875 3.083,2.073 0.49,0.198 10 false 4 (FP-) 0.146,0.104 0.448,0.406 0.302,0.302 10 false *a

b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test /Control the Fuel Pump Duty.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FP+) - 4 (FP-) FPC Duty: 25% 3.2 to 4.05 V
3 (FP+) - 4 (FP-) FPC Duty: 80% 8.8 to 12.5 V


Text in Illustration
*a Component without harness connected
(Fuel Pump)


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump/Speed.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FP+) - 4 (FP-) ON
(FPC Duty: 25%)
9.0 to 14.0 V



HINT:
·

Be sure to measure the voltage with all the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




OK

3.CHECK HARNESS AND CONNECTOR (ECM - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

6.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (ECM - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-19 (FPC) - G12-2 (FPC) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-19 (FPC) or G12-2 (FPC) - Body ground Always 10 kΩ or higher




OK

4.REPLACE FUEL PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE FUEL PUMP ASSEMBLY
a.

Replace the fuel pump assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP>REMOVAL).



NEXT

5.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).

OK:

Malfunction has been repaired successfully.




OK

END

NG

6.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP ECU>REMOVAL).



NEXT

7.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).

OK:

Malfunction has been repaired successfully.




OK

END

NG

8.INSPECT FUEL PUMP CONTROL ECU ASSEMBLY (POWER SOURCE VOLTAGE)
a.
U146774E03
0.677,1.771 1.01,1.219 true 1.594,0.531 1.885,0.719 0.292,0.188 10 false G12 0.104,0.094 0.469,0.292 0.365,0.198 10 false *a 0.396,1.792 0.813,2.042 0.417,0.25 10 false 1(+B)

Disconnect the fuel pump control ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G12-1 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector:
(to fuel pump control ECU)



OK

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

14.CHECK HARNESS AND CONNECTOR (C/OPEN RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Disconnect the fuel pump connector.


b.

Disconnect the fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
G7-4 (FP-) - G12-5 (FP-) Always Below 1 Ω
G7-3 (FP+) - G12-6 (FP+) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
G7-4 (FP-) or G12-5 (FP-) - Body ground Always 10 kΩ or higher
G7-3 (FP+) or G12-6 (FP+) - Body ground Always 10 kΩ or higher




OK

10.INSPECT FUEL PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FUEL PUMP ASSEMBLY
a.

Inspect fuel pump assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP>INSPECTION).



OK

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

REPLACE FUEL PUMP ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-19 (FPC) - G12-2 (FPC) Always Below 1 Ω
G12-4 (E)- Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-19 (FPC) or G12-2 (FPC) - Body ground Always 10 kΩ or higher




OK

12.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP ECU>REMOVAL).



NEXT

13.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).

OK:

Malfunction has been repaired successfully.




OK

END

NG

14.CHECK HARNESS AND CONNECTOR (C/OPEN RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Remove the C/OPEN relay from the engine room relay block assembly.


b.

Disconnect the fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPEN relay terminal 3 - G12-1 (+B) Always Below 1 Ω
C/OPEN relay terminal 1 - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C/OPEN relay terminal 3 or G12-1 (+B) - Body ground Always 10 kΩ or higher




OK

15.INSPECT TERMINAL VOLTAGE (C/OPEN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT TERMINAL VOLTAGE (C/OPEN RELAY)
A280180E01
0.171,0.422 0.333,0.608 0.163,0.186 10 *1 0.462,3.277 0.654,3.447 0.192,0.169 10 *2

a.

Remove the C/OPEN relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C/OPEN relay terminal 5 - Body ground IG ON 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block Assembly
*2 C/OPEN Relay Terminal



OK

16.CHECK HARNESS AND CONNECTOR (C/OPEN RELAY - ECM - IG2 RELAY)

NG

16.CHECK HARNESS AND CONNECTOR (C/OPEN RELAY - ECM - IG2 RELAY)
a.

Disconnect the ECM connector.


b.

Remove the C/OPEN relay and IG2 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPEN relay terminal 2 - A33-27 (IGSW) Always Below 1 Ω
C/OPEN relay terminal 2 - IG2 relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C/OPEN relay terminal 2, A33-27 (IGSW) or IG2 relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR