Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stores the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. DTC Detection Condition Trouble Area
P0420 Diagnostic value is more than the standard value.
(2 trip detection logic)
·

Gas leakage from exhaust system

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Front exhaust manifold assembly (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)



CATALYST LOCATION

A280655E03
1.521,5.354 1.75,4.698 1.75,4.698 1.844,4.698 true 4.177,4.604 4.417,3.948 4.417,3.948 4.5,3.948 true 2.188,6.156 2.26,6.542 2.26,6.542 2.354,6.542 false 0.969,5.333 0.844,5.719 0.844,5.719 0.667,5.719 false 0.74,3.813 1,3.396 1,3.396 1.271,3.396 false 3.073,4.531 3.219,4.135 3.219,4.135 3.302,4.135 false 5.25,4.385 5.49,4.896 5.49,4.896 5.573,4.896 false 3.615,2.792 3.365,2.396 3.365,2.396 2.969,2.396 false 5.031,1.271 4.875,1.531 4.875,1.531 4.563,1.531 false 1.917,4.625 2.156,4.802 0.24,0.177 10 false *1 4.583,3.865 4.823,4.042 0.24,0.177 10 false *2 2.427,6.448 2.667,6.625 0.24,0.177 10 false *3 0.448,5.656 0.688,5.833 0.24,0.177 10 false *4 1.344,3.333 1.583,3.51 0.24,0.177 10 false *5 3.375,4.052 3.615,4.229 0.24,0.177 10 false *6 5.646,4.813 5.885,4.99 0.24,0.177 10 false *7 2.771,2.313 3.01,2.49 0.24,0.177 10 false *8 4.354,1.448 4.594,1.625 0.24,0.177 10 false *9

Text in Illustration
*1 TWC: Front Catalyst *2 TWC: Rear Catalyst
*3 Exhaust Manifold *4 Air Fuel Ratio Sensor
*5 Heated Oxygen Sensor *6 Front Exhaust Pipe Sub-Assembly
*7 Front Exhaust Pipe Assembly *8 Center Exhaust Pipe Assembly
*9 Tail Exhaust pipe Assembly - -

MONITOR DESCRIPTION

The ECM uses diagnostic values to determine deterioration of the catalyst. If the diagnostic value exceeds a specified value, the catalyst is considered deteriorated, and the DTC is stored.

U146806E03
4.802,3.302 5.01,2.917 5.01,2.917 5.073,2.917 false 5.906,3.51 6.052,3.51 false 0.594,0.792 1.781,1.125 1.188,0.333 10 false Catalyst status 0.521,1.323 2.031,1.823 1.51,0.5 10 false Air fuel ratio sensor output waveform 0.49,1.823 1.958,2.281 1.469,0.458 10 false Heated oxygen sensor status 0.49,2.333 1.958,2.792 1.469,0.458 10 false Heated oxygen sensor output waveform 2.323,1.938 2.99,2.177 0.667,0.24 10 false Normal 3.49,1.938 4.156,2.177 0.667,0.24 10 false Normal 4.969,1.938 6.104,2.177 1.135,0.24 10 false Slow response 2.313,0.792 2.979,1.031 0.667,0.24 10 false Normal 3.396,0.802 4.219,1.042 0.823,0.24 10 false Malfunction 5,0.802 5.823,1.042 0.823,0.24 10 false Malfunction 0.646,3.406 1.844,3.792 1.198,0.385 10 false Diagnosis value 2.417,4.01 3.083,4.25 0.667,0.24 10 false Pass 3.365,4.01 4.25,4.25 0.885,0.24 10 false Fail detected 4.563,4.031 5.281,4.469 0.719,0.438 10 false Fail not detected 5.521,4.063 6.406,4.302 0.885,0.24 10 false Fail detected 5.135,2.844 6.677,3.125 1.542,0.281 10 false Effect of response time 6.115,3.417 7.01,3.75 0.896,0.333 10 false Adjusted CM

The diagnostic values are based upon the catalyst monitor value (CM) calculated by changes in the air fuel ratio sensor lambda and changes in the heated oxygen sensor output voltage, and in the response rate calculated from the heated oxygen sensor response time.

A397570E01
2.958,0.938 3.208,0.51 3.208,0.51 3.323,0.51 false 3.396,2.104 3.083,1.656 3.083,1.656 2.958,1.656 false 1.938,0.865 1.656,0.333 1.656,0.333 1.542,0.333 false 1.594,2.177 1.833,1.563 1.833,1.563 1.938,1.563 false 0.354,0.75 1.625,1.104 1.271,0.354 10 false Lambda of air fuel ratio sensor 0.219,1.552 1.604,1.906 1.385,0.354 10 false Output voltage of heated oxygen sensor 0.906,0.25 1.594,0.438 0.688,0.188 10 false Value (A) 3.385,0.427 4.073,0.615 0.688,0.188 10 false Value (B) 3.219,2.146 3.906,2.333 0.688,0.188 10 false Value (b) 1.375,2.198 2.063,2.385 0.688,0.188 10 false Value (a) 3.302,1.406 3.854,1.583 0.552,0.177 10 false CM = 3.927,0.99 6.792,1.354 2.865,0.365 10 false Integrated value of deviation of heated oxygen sensor output voltage (Value (a) + (b) + ... ) 4.25,1.615 6.104,1.99 1.854,0.375 10 false Integrated value of deviation of lambda (Value (A) + (B) + ... )

*: Diagnostic Value = CM X (1 + Response rate)

CONFIRMATION DRIVING PATTERN

A280672E03
3.25,0.5 3.552,0.719 0.302,0.219 10 false [A] 5.49,1.573 5.792,1.792 0.302,0.219 10 false [B] 2.792,2.365 4.302,2.583 1.51,0.219 10 false 20 minutes or more 5.01,2.365 6.365,2.583 1.354,0.219 10 false 1 minute or more 0.063,0.667 1.198,1.063 1.135,0.396 10 false 80 km/h (50 mph) 0.219,1.688 1.219,2.063 1,0.375 10 false 0 km/h (0 mph) 0.177,0.115 1.188,0.51 1.01,0.396 10 false Vehicle Speed 6.385,2.24 7.104,2.635 0.719,0.396 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

Check the engine coolant temperature is 20°C (68°F) or less at engine started.


7.

Perform the following the confirmation driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


(a)

Drive the vehicle at 80 km/h (50 mph) or more for 20 minutes or more [A].

(b)

Stop the vehicle.

(c)

Idle the engine for 1 minute or more [B].


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0420.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CONDITIONING FOR SENSOR TESTING

A093766E60
4.813,2.344 4.813,2.438 false 5.104,2.354 5.26,2.552 5.26,2.552 5.469,2.552 false 3.583,0.333 3.813,0.531 0.229,0.198 10 false [C] 0.677,0.135 1.625,0.333 0.948,0.198 10 false Engine Speed 0.875,0.469 1.542,0.667 0.667,0.198 10 false 3000 rpm 0.896,0.958 1.542,1.177 0.646,0.219 10 false 2000 rpm 1.208,1.688 1.583,1.885 0.375,0.198 10 false Idling 0.448,2.094 1.542,2.302 1.094,0.208 10 false Power Switch off 1.688,1.917 1.917,2.115 0.229,0.198 10 false [A] 2.146,1.698 2.375,1.896 0.229,0.198 10 false [B] 4.729,0.333 4.958,0.531 0.229,0.198 10 false [D] 5.01,0.823 5.24,1.021 0.229,0.198 10 false [D] 2.146,2.396 2.948,2.594 0.802,0.198 10 false Warming up 3.229,2.417 4.396,2.615 1.167,0.198 10 false At least 3 minutes 4.521,2.438 5.208,2.635 0.688,0.198 10 false 2 seconds 5.51,2.469 6.198,2.667 0.688,0.198 10 false 2 seconds 6.5,2 6.885,2.198 0.385,0.198 10 false Time

1.

Connect the GTS to the DLC3 [A].

2.

Start the engine and warm it up with all the accessories switched off, until the engine coolant temperature stabilizes [B].

3.

Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes [C].

4.

While running the engine at 3000 rpm and 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS [D].


HINT:
·

If either of the voltage outputs of either the air fuel ratio or heated oxygen sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor.

·

If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions.



A199479E37
0.25,0.104 4.594,0.271 4.344,0.167 10 false Voltage output when air-fuel ratio control not performed: 2.438,0.531 3.573,0.698 1.135,0.167 10 false Normal Catalyst 4.76,0.542 6.135,0.729 1.375,0.188 10 false Deteriorated Catalyst 2.406,2.99 3.281,3.188 0.875,0.198 10 false 10 seconds 4.958,3 5.792,3.167 0.833,0.167 10 false 10 seconds 1.49,0.823 1.875,0.969 0.385,0.146 10 false 2.4 V 1.479,1.25 1.865,1.396 0.385,0.146 10 false 2.0 V 1.49,2.115 1.885,2.323 0.396,0.208 10 false 1.0 V 1.604,2.75 1.917,2.979 0.313,0.229 10 false 0 V 0.094,2.271 1.323,2.958 1.229,0.688 10 false Waveform of Heated Oxygen Sensor behind Three-Way Catalytic Converter 0.083,0.823 1.375,1.542 1.292,0.719 10 false Waveform of Air Fuel Ratio Sensor in front of Three-Way Catalytic Converter

CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B


HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (Control the Injection Volume)

B

2.PERFORM ACTIVE TEST USING GTS (Control the Injection Volume)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume


f.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of - 12.5% to +12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 2.0 V
-12.5% Lean Higher than 2.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status
AFS Voltage B1S1
Status
O2S B1S2
A/F Condition and A/F and
HO2 Sensor Conditions
Misfire Main Suspected Trouble Areas Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-Way Catalytic Converter (TWC)

·

Gas leakage from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leakage from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leakage from exhaust system


Lean Lean Actual air-fuel ratio lean May occur
·

Extremely rich or lean actual air-fuel ratio

·

Gas leakage from exhaust system


D
Rich Rich Actual air-fuel ratio lean -
·

Extremely rich or lean actual air-fuel ratio

·

Gas leakage from exhaust system




Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 2.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 2.0 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



A

3.CHECK FOR EXHAUST GAS LEAK

B

C

5.CHECK FOR EXHAUST GAS LEAK

D

6.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

4.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

4.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST)
a.

Replace the exhaust manifold (TWC: front catalyst) (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>EXHAUST MANIFOLD>REMOVAL).



NEXT

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

5.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

CHECK CAUSE OF EXTREMELY RICH OR LEARN ACTUAL AIR FUEL RATIO

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT