Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes.

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor.

Resistor and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0112 Intake air temperature sensor voltage is less than 0.4 V for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


P0113 Intake air temperature sensor voltage is 4.707 V or more for 0.5 seconds or more.
(1 trip detection logic)

HINT:

When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
120°C (248°F) Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0112 or P0113.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280061E03
0.844,2.875 2.729,3.26 1.885,0.385 10 false Intake Air Temperature Sensor (Mass Air Flow Meter) 5.698,2.813 6.115,3.01 0.417,0.198 10 false ECM 0.844,2.698 1.344,2.958 0.5,0.26 10 false C16 4.958,1.396 5.385,1.677 0.427,0.281 10 false A33 5,1.198 5.25,1.51 0.25,0.313 10 false 12 4.958,2.115 5.396,2.375 0.438,0.26 10 false A36 5,1.917 5.25,2.229 0.25,0.313 10 false 29 2.875,2 3.125,2.313 0.25,0.313 10 false 2 2.875,1.292 3.125,1.604 0.25,0.313 10 false 1 2.479,1.292 2.99,1.667 0.51,0.375 10 false THA 2.594,2 2.979,2.333 0.385,0.333 10 false E2 5.302,1.292 5.802,1.74 0.5,0.448 10 false THA 5.323,2.01 5.646,2.354 0.323,0.344 10 false E1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


e.

Read the value displayed on the GTS.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
120°C (248°F) B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 215°C (419°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
U146749E03
1.177,3.76 0.802,4.25 true 1.542,3.76 1.813,4.281 true 0.25,2.813 0.5,3 0.25,0.188 10 false *a 0.833,1.5 1.083,1.688 0.25,0.188 10 false *1 2.625,1.51 2.875,1.698 0.25,0.188 10 false *2 2.271,0.615 2.594,0.802 0.323,0.188 10 false THA 2.271,0.969 2.479,1.156 0.208,0.188 10 false E1 0.219,3.563 0.531,3.729 0.313,0.167 10 false C16 0.667,4.292 0.969,4.604 0.302,0.313 10 false THA 1.771,4.333 1.969,4.646 0.198,0.313 10 false E2

Disconnect the mass air flow meter connector.


b.

Connect terminals 1 and 2 of the mass air flow meter connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


g.

Read the value displayed on the GTS.

Standard value:

Higher than 120°C (248°F)


Text in Illustration
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)



OK

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A33-12 (THA) - C16-1 (THA) Always Below 1 Ω
A36-29 (E1) - C16-2 (E2) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A280086E06
0.771,1.531 1.021,1.719 0.25,0.188 10 false *1 2.563,1.531 2.813,1.719 0.25,0.188 10 false *2 2.229,0.594 2.542,0.781 0.313,0.188 10 false THA 2.229,0.969 2.427,1.156 0.198,0.188 10 false E1

Disconnect the mass air flow meter connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Mass Air Flow Meter
*2 ECM



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-12 (THA) or C16-1(THA) - Body ground Always 10 kΩ or higher
A36-29 (E1) or C16-2 (E2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR